JB/T 10231.3-2001 Tool product testing methods Part 1: End mills

JB/T 10231.3-2001 This standard specifies the testing methods and testing instruments for various end mills. This method is not the only one. This standard is applicable to the testing of end mills produced according to GB/T 6117.1~6117.3, GB/T 6118, GB/T 1109. This standard was first issued in March 2001. JB/T 10231.3-2001 Tool product testing methods Part 1: End mills JB/T10231.3-2001 Standard download decompression password: www.bzxz.net

ic.525.1nn.n1
Machinery Industry Standard of the People's Republic of China
JB/T10231.3-2001
Tool Product Inspection Methods
Part 3: End Mills
Tool inspaction methods pert3:end mitls2001-03-29 Issued
China Machinery Industry Federation
2001-07-01 Implementation
JB/T18231.3—2001
This standard was first issued on March 29, 2001. Long Yan
This standard was proposed and approved by the National Standardization Technical Committee. This standard was drafted by Chengdu Institute of Technology. The main drafters of this standard are: Bi Shichang and Ma Guobin. This standard is issued for the first time.
Machinery Industry Standard of the People's Republic of China
Testing Methods for Cutting Tool Products
Part 3: End Mills
Tool iatpacto etheds part 3saad m[t.JB/T10231.3—2001
This standard specifies the inspection methods and inspection tools for various end mills when inspecting finished products. These methods are not exclusive. This standard applies to the inspection of end mills produced in accordance with GB/6117.1.-6113, GBT0118 and GB/F110. 2. ReferencesbZxz.net
The texts contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published: the versions shown are valid. All standards will be revised independently. The parties using this standard shall consider the possibility of using the latest versions of the following standards. GB/T 1109.-1985
GB/T 6117.11996
GB/F 61172—1996
GB/T 6117.3—1996
GB/T 6118—-1996
JB/T10231.1 2001
3 Inspection principles
Short Morse shank end mills
End mills Part 1: Types and dimensions of straight end mills End mills Part 2: Types and dimensions of Morse taper end mills End mills Part 3: Types and dimensions of 7:24 shank end mills Technical requirements for end mills
Tool product inspection methods Part 1: General product standards and drawings,
4 Inspection methods and inspection specifications
Appearance inspection shall be in accordance with the provisions of Chapter 4 of JB/10231.1-2001. 4.1 Surface roughness
Surface roughness inspection shall be in accordance with the provisions of Chapter 5 of 3B1023112001. 4.3 Testing
4.3. 1. The detection method of the radial force of the rusted part axis on the circumference of the detection piece is shown in Figure 1 and Figure 2. Place the milling cutter on the V-shaped soft, the handle passes through a steel ball and a positioning block, and the dial indicator probe is vertically touched on the circumferential blade within 5mm from the end of the end mill: read the dial readings on each cutting system in turn, and take the difference between the maximum and minimum values. The end face of the adjacent tooth difference is subjected to the force on the end face of the handle axis. The detection method is shown in Figure 1 and Figure 2. Place the end mill on the √-shaped iron, the handle passes through a steel ball and a positioning block, and the dial indicator probe is melted on the end mark within 2m of the original outer circle. , read the dial indicator readings on the sharpening edge in turn, and take the difference between the maximum and minimum values
Approved by China Machinery Industry Federation on 201-03-29 and implemented on 2003-07-01
4.3.2 Testing equipment
JB/T102313-2001
Testing method for the vibration of a straight-handled vertical knife
Figure 2 Testing method for the vibration of a straight-handled vertical knife
Positioning leather
Special replacement
The support rod with a graduation value of 0.002mm is used for a dial indicator or a dial indicator, a flat plate, and a magnetic table stand, V-shaped iron, steel ball. 4.4 Diameter and working part diameter cone
4.4.1 Inspection method
The diameter shall be inspected in accordance with the provisions of 10.1 in T102311-2001. The working part diameter strength is expressed by the working part diameter difference. Point A is measured near the tip of the tool. Points A and C are approximately distributed in the middle and rear. The absolute value of the reading difference between points A and B and the absolute value of the reading difference between points A and C are taken respectively. For milling cutters with a diameter less than 16 mm, only points A and C are allowed.
4.4.2 Pull test equipment
Outer diameter ten-point ruler , two-groove micrometer, five-groove micrometer. 4.5 The shank diameter of the green shank end mill shall be tested in accordance with the provisions of 10.1 in JB/T10231.1-2001. 4.6 The shank diameter of the taper shank end mill shall be tested in accordance with the provisions of Chapter 6 and Chapter 1 in JB/T10231.1-2001. 4.7 The overall length and working part length shall be tested in accordance with the provisions of 10.1 in JB/T10231.1-2001. 4. 8 Hardness
The hardness test shall be in accordance with the provisions of JB/T10231.1-2001 11.3. 4.9 Marking and packaging
The marking and packaging test shall be in accordance with the provisions of Chapter 13 and Section 14 of JB/T10231.1-2001.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.