QB/T 1583-2005 Leather gloves sizes

This standard specifies the definition, application, series, marking, measurement and control values ​​of leather gloves. This standard applies to all types of daily leather gloves. Artificial leather and synthetic leather daily gloves can be used as a reference. This standard does not apply to gloves with special uses and requirements. QB/T 1583-2005 Leather Gloves QB/T1583-2005 Standard download decompression password: www.bzxz.net

Ec 59. 14. 35
Classification number: Y48
Registration number: 157322005wwW.bzxz.Net
Light Industry Standard of the People's Republic of China
QB/T1583—2005
Generation Q13/583-1992
Leather gloves size
Size desionation of leather gloves gloves2005-03-19 release
National Development and Reform Commission of the People's Republic of China2005-09-01 implementation
This standard is for 0B/T15831992. Leather gloves No. 3, compared with 93/T1583-1992, this standard has the following changes: - Keep consistent with clothing standards, "type" is changed to "type" QB/T1583-2C05
Special specification has been refined: "select leather, synthetic year for use according to the date: not suitable for special use and effective" - ​​standardize terms and definitions:
- Change "type" to "number", and change "number" to "number", keep consistent with clothing size indication method, - According to the human body Model changes, the "control number elimination" was adjusted, this standard was proposed by China Light Industry Cooperation Association, and the national industry standardization technical committee (SAC/1252) was drafted by this standard: the Secretariat of the National Leather Industry Standardization Technical Committee, China National Institute of Standardization. This standard was issued in May 2012, and this is the first time. The implementation of this standard is based on the industrial standard Q15831902 Leather Gloves Model 1 Scope
Leather Gloves Number
Q0/T15832005
This standard defines the definition of leather gloves, minimum notes, number series, number mark, number part, and control part number mark.
This mark is generally used for all kinds of sets, artificial leather, synthetic leather sets are used as guides: this mark is not suitable for special selection and requirements. 2 Technical specifications and definitions
The following technical specifications and definitions are applicable to the standard of woodworking. 2.1
refers to the length of the cabinet, which is usually expressed in meters, and is the basis for design and selection of the actual length. 2.2
The length of the cabinet is expressed in meters, which is the basis for design and selection of the cabinet. 23
Control position value
refers to the value of the main position of the cabinet, which is the net body value; it is the basis for design and specification. 3 Type application
The following mark is the range of length: the length of the cabinet is close to this number: for example: No. 170, suitable for people with hand length of 165m~175m, with a length of 165m~175m.
The lower set of 1 standard is applicable to the person who chooses the cabinet, for example: 185, 180-190 for the person who is 180, and so on,
4 model series
4.1 model series is set
With the standard body (male height 185mm, female circumference 170mm, female circumference 185mm) as the center, the two sides increase or decrease in reverse order, with 10 points for length and 10 points for height respectively, to form a special model series. According to special circumstances, it can be combined according to the five new models in this size series,
4.2 Size end name
length is accurate to mm, such as 182m nominal 180183mm nominal 185m4.3 Adult men's glove size series
or men's set size series are all compared with Table 1.
QB/11583—2006
4.4 War women's set size series
Stock women's number series see Table 2
Size mark
Table 1 Adult men's glove size series
Table 2 Adult women's glove size series
The best is the pullover
The medium is the oxygen meter
Almost enough, the standard type and the amateur line are close to the type. For example: 170/185. The table is less than 〖170mm, the figure value is 185
6 No. 6 type measurement
6 hand length
two and a half blue standard, and the straight line distance from the midpoint of the curved end to the middle fingertip is measured according to the method diagram. 6.2 Learning circumference
three meeting conditions: the middle ruler side meeting point, through the learning straight teaching plan will be the outer side and the back mountain, judge the six reading learning point points [sand quantity, use the control to violate the half and must be in the card to shoot its straight, measurement method see Figure 1.2
T15e3-2005
front free meter
1: 2:: - length: a small length
8 a brown finger example: 9 from -: U is two: 11 minister =: 12 a learning difference: 11 a learning five: 14 case width: 14 - goods protection width, 16 a width: 17 yuan finger width: 18 a width, 19 net use, 20 · people meet to go to the hand shape measurement schematic diagram
the control part number Bo
7.1 adult male child set series control part value request male set series test value see table 3, table 4 table 3 Table 4 Values ​​of control parts of adult men's gloves number series (I? Jing
2 Values ​​of control parts of adult women's gloves number series 195
Values ​​of control parts of adult women's gloves number series see clothing 5, Table 6295
Table 5 Values ​​of control parts of adult women's gloves number series (I) Top
Food project
Table of control parts of adult women's gloves number series:) Type
Single sex is the key
Single product related
Unit is meter
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.