GB/T 3487-1996 Automobile rim specification series

This standard specifies the rim profile shape and size, rim diameter series, rim nominal diameter and inspection circumference of the matching part between the rim and the tire. This standard is applicable to various rims. GB/T 3487-1996 Automobile rim specification series GB/T3487-1996 Standard download decompression password: www.bzxz.net

National Standard of the People's Republic of ChinawwW.bzxz.Net
Specification Series of Automobile Rim
Rim contours for motor vehiclesSubject Content and Scope of Application
GB/T 3487—1996
Replaces GB3487—-89
This standard specifies the shape and size of the rim contour (referred to as rim contour) of the matching part between the automobile rim and the tire, the rim diameter series, the rim calibration diameter and the inspection circumference.
This standard applies to various automobile rims.
25° deep groove rim (5°DC)
The contour shape and size of the 2.15° deep groove rim shall comply with the provisions of Figure 1 and Tables 1 and 2. *1,3
Note: The double-dotted line is an optional contour range. Figure 1
Profile Specifications
51/2JK
Approved by the State Administration of Technical Supervision on February 27, 199670
Implemented on October 1, 1996
51/2JJ
GB/T3487-1996
The 5° deep groove rim profiles (except 3.00B) with flange codes B, J, JJ and JK listed in Tables 1 and 2 can be rounded, flat or frame-type bead seats. The rounded peak is used for the rim's assembly and disassembly edge (usually located on the outside of the vehicle after installation) or the non-assembly edge (usually located on the inside of the vehicle after installation), the flat peak is used for the rim's assembly and disassembly edge (both sides are assembly and disassembly edges and both sides can use flat peaks), and the frame is used for the non-assembly edge of the rim. The shapes and sizes of the round peak, flat peak and frame type bead seat should comply with the requirements of Figures 2, 3 and 4. R10.5**-5
21.5 ±0.8
(21*for JK type wheel)
Rim non-disassembly edge (inside of vehicle))
5°±1°
5°±1°
21.5±0.8
(21*for JK type wheel))
Rim disassembly edge (outside of vehicle)
Rim non-disassembly edge
Rim non-disassembly edge
GB/T3487-1996
Reference!
Rim disassembly and assembly edge
Rim disassembly and assembly edge
The diameter series, nominal diameter and circumference inspection dimensions of 2.25° deep groove rims shall conform to the provisions of Table 3. Table 3
Rim nominal
Diameter code
Corresponding rim profile specifications
3.50B,4.00B,4.50B
3. 00B,3. 50B,4. 00B,4. 50B,5. 00B,4J
4.50B,5.00B,5.50B,6.00B,4 1/2J4J,4 1/2J,5J,5 1/2J,
51/2JJ,5JK
4J,41/2J,5J,51/2J,6J，
6 1/2J,7J.10J,5JK,5 1/2JK
5J,51/2J,6J,61/2.7J,8J，
5.00E,5JK,5 1/2JK
Calibration diameter
Ball tape ruler
Measurement of ball diameter
Inspection spindle
Rim inspection
Circumference deviation
3 Half-deep groove rim (SDC)
GB/T3487--1996
3.1 The profile shape and size of the half-deep groove rim shall conform to the provisions of Figure 5 and Table 4. R<6.5
Rim profile specification
5°±1°
The diameter series, calibration diameter and circumference inspection size of the half-deep groove rim shall conform to the provisions of Table 5. Table 5
Nominal
Diameter code of rim
Corresponding rim profile specification
5. 50F, 6. 00G
5.50F, 6.00G, 6.50H
Nominal diameter
Ball tape ruler
Measurement ball diameter
Inspection spindle
Rim inspection
Circumference deviation
Type 1 flat bottom rim (FB-I)
GB/T3487—1996
The profile shape and size of type 1 flat bottom rim shall comply with the provisions of Figure 6 and Table 6. A
Rim profile specification
The diameter series, nominal diameter and profile inspection size of type 1 flat bottom rim shall comply with the provisions of Table 7. Table 7
Nominal rim
Diameter code
Corresponding rim profile specifications
6.0,6.5,9.0
6. 0,6.5,7. 0,7.5,
8. 0,8. 5,9.0,10. 0
Calibrated diameter
Measurement of ball diameter with ball tape ruler
Inspection spindle
Rim inspection
Circumference deviation
Type I flat bottom rim (FB-I)
GB/T3487—1996
The profile shape and size of type I flat bottom rim shall conform to the requirements of Figure 7 and Table 8. R.8
Rim profile specifications
The diameter series, nominal diameter and profile inspection dimensions of type 1 flat-bottom rims shall comply with the provisions of Table 9. Table 9
Rim nominal
Diameter code
Corresponding rim profile specifications
6.50T.7.00T.7.50V
8. 00V.8. 50V,9. 00V
Nominal diameter
Rim inspection circumference
615° deep groove rim (15°DC)
GB/T 3487—1996
6.1The profile shape and dimensions of 15° deep groove rims shall comply with the provisions of Figure 8 and Table 10. A
19 ~ 29
R12.7±1.5/
（丝考）
R=16The fillet radius can be reduced, but it must be increased by 1 at the same time to ensure the needs of tire disassembly and assembly. The valve hole can be located on the side of the rim groove or on the bottom. Figure 8
Rim specification code
17.5×5.25
17.5×6.00
19.5×6.00
22.5×6.00
17.5×6.75
19.5×6. 75
22.5X6.75
19.5×7.50
22.5×7.50
19.5×8.25
22.5×8.25
24.5×8.25
22.5× 9.00
24.5×9.00
22.5X9.75
On the
side of the rim groove is
On the
bottom of the rim groove is
GB/T3487—1996
The diameter series, nominal diameter and profile inspection dimensions of 15° deep groove rims shall conform to the provisions of Table 11. Table 11
Rim nominal
Diameter code
Corresponding rim profile specifications
5. 25, 6. 00, 6. 75
6.00.6.75.7.50.8.25
6.00, 6.75, 7.50, 8.25, 9.00, 9.758.25, 9.00
Additional remarks:
This standard is proposed by the Automobile Industry Department of the Ministry of Machinery Industry. Calibration diameter
This standard is under the jurisdiction of the National Technical Committee for Standardization of Tires and Rim. Deviation
This standard was drafted by Changchun Automobile Research Institute and Tianjin Wheel Experiment Center. The main drafters of this standard are Mou Xianfang and Gu Gang. Ball tape measure
Measure ball diameter
Inspect spindle
1 946. 28
Inspect wheel rim
Circumference deviation
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.