Technical data of Type DB-489 electronic glass
time:
2024-07-14 14:31:41
- SJ/T 10588.23-1994
- Abolished
Standard ID:
SJ/T 10588.23-1994
Standard Name:
Technical data of Type DB-489 electronic glass
Chinese Name:
DB-489型电子玻璃技术数据
Standard category:
Electronic Industry Standard (SJ)
-
Date of Release:
1994-08-08 -
Date of Implementation:
1994-12-01 -
Date of Expiration:
2008-01-20
China Standard Classification Number:
General>>Standardization Management and General Provisions>>A01 Technical Management
alternative situation:
Replaced by SJ/T 11369-2007
Skip to download
Summary:
SJ/T 10588.23-1994 Technical data of DB-489 electronic glass SJ/T10588.23-1994 Standard download decompression password: www.bzxz.net
Some standard content:
Electronic Industry Standard of the People's Republic of ChinabZxz.net
Technical data of type DB-489 electronic glass
Technical data of type DB-489 electronic glass 1 Subject content and scope of application
This standard specifies the chemical composition and physical and chemical performance indicators of DB-489 electronic glass. This standard is applicable to glass materials used in the neck of black and white picture tubes. 2 Reference standards
Standard method for chemical analysis of electronic glass
GB9000
GB9622
3 Technical requirements
Test method for physical and chemical properties of electronic glass
3.1 Chemical composition See Table 1.
Chemical composition
3.2 Physical and chemical performance indicators are shown in Table 2
Weight percentage
56.3±1.5
2.90±1.0
Approved by the Ministry of Electronics Industry of the People's Republic of China on August 8, 1994 SJ/T10588.23--94
Test method
GB9000.12
GB9000.10
Implemented on December 1, 1994
Indicator name
SJ/T10588.23-94
Average linear thermal expansion coefficient α in the range of 0 to 300℃ Density
Softening point
Annealing point
Strain point|| tt||Dielectric loss tangent tgox104 at frequency 6MHz and temperature 20C
Volume resistivity Igp at 350℃
Thermal stability
Water resistance and chemical stability level
(91.0±2.0)×10-7
3.050±0.015
620±10
435±10
395±10
≥110
Test method
GB9622.81)
GB9622.11
Note: 2) Articles 4.5 and 4.6 are combined and carried out as follows: The measurement starts from the starting point, keeps warm at 300℃ for 10min, and then starts measuring. Continue to increase the furnace temperature, measuring every 10℃ until the temperature reaches 390℃. Additional Notes:
This standard is under the jurisdiction of the Standardization Institute of the Ministry of Electronics Industry. This standard was drafted by Tianjin Jinjing Glass Shell Co., Ltd. and the Standardization Institute of the Ministry of Electronics Industry. The main drafters of this standard are Li Zongpu, Liu Chengjun, Qu Yuan, and Shen Bopeng.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Technical data of type DB-489 electronic glass
Technical data of type DB-489 electronic glass 1 Subject content and scope of application
This standard specifies the chemical composition and physical and chemical performance indicators of DB-489 electronic glass. This standard is applicable to glass materials used in the neck of black and white picture tubes. 2 Reference standards
Standard method for chemical analysis of electronic glass
GB9000
GB9622
3 Technical requirements
Test method for physical and chemical properties of electronic glass
3.1 Chemical composition See Table 1.
Chemical composition
3.2 Physical and chemical performance indicators are shown in Table 2
Weight percentage
56.3±1.5
2.90±1.0
Approved by the Ministry of Electronics Industry of the People's Republic of China on August 8, 1994 SJ/T10588.23--94
Test method
GB9000.12
GB9000.10
Implemented on December 1, 1994
Indicator name
SJ/T10588.23-94
Average linear thermal expansion coefficient α in the range of 0 to 300℃ Density
Softening point
Annealing point
Strain point|| tt||Dielectric loss tangent tgox104 at frequency 6MHz and temperature 20C
Volume resistivity Igp at 350℃
Thermal stability
Water resistance and chemical stability level
(91.0±2.0)×10-7
3.050±0.015
620±10
435±10
395±10
≥110
Test method
GB9622.81)
GB9622.11
Note: 2) Articles 4.5 and 4.6 are combined and carried out as follows: The measurement starts from the starting point, keeps warm at 300℃ for 10min, and then starts measuring. Continue to increase the furnace temperature, measuring every 10℃ until the temperature reaches 390℃. Additional Notes:
This standard is under the jurisdiction of the Standardization Institute of the Ministry of Electronics Industry. This standard was drafted by Tianjin Jinjing Glass Shell Co., Ltd. and the Standardization Institute of the Ministry of Electronics Industry. The main drafters of this standard are Li Zongpu, Liu Chengjun, Qu Yuan, and Shen Bopeng.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- JB/T 3411.118-1999 Dimensions of end milling cutter shanks with Morse taper shanks and end keys
- GB/T 8570.4-1988 Determination of residual content of liquid anhydrous ammonia - Volumetric method
- GB/T 22273-2008 Advisory document for good laboratory practice:The application of the principles of GLP to in vitro studies
- GB/T 3730.3-1992 Terms and definitions for motor vehicles and trailers Vehicle dimensions
- JB/T 10030-1999 Grating Line Displacement Measurement System
- HG/T 2095-1991 Coating urea
- QB/T 1594-1992 Circular saw sharpening machine
- JB/T 10404-2004 Operation and management specification for off-grid wind power centralized power supply system
- GB/T 8151.13-2000 Chemical analysis methods for zinc concentrates - Determination of germanium content
- JJF 1030-1998 Measurement and Test Norm of Thermostatic Baths Metrological Characteristics
- JB/T 8018.3-1999 Machine tool fixture parts and components adjustment V-blocks
- JB/T 5508-1991 ZSL Cold Ore Vibrating Screen
- QB/T 3657.2-1999 Specification for alkyd varnish and phenolic varnish finishing process for wooden furniture
- GB/T 19437-2004 Graphic technology—Spectral measurement and colorimetric computation for graphic arts images
- HG/T 2412.1-1992 Test methods for rubber threads Determination of rubber thread thickness
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail:wymp4wang@gmail.com