GB/T 4678.4-2003 Die casting parts Part 4: Shoulder guide pins

This part specifies the dimensions and tolerances of shoulder guide pins for die casting moulds. This part applies to shoulder guide pins and push plate guide pins used in die casting moulds. This part also gives material guidelines and hardness requirements, and specifies the marking of shoulder guide pins. GB/T 4678.4-2003 Die casting mould parts Part 4: Shoulder guide pins GB/T4678.4-2003 Standard download decompression password: www.bzxz.net

/14 models of music generals. points!
Part 1: Success:
Part 3: Form:
Part 4: Capability, with enlightenment!
Part 5: Leading students!
Part 1: School year,
Part 2: Success! Part
Common 3 energy points: version
Part 3
Part 1: Reduction rod
Part 13: Network:
-Part 14: Acceptance
Every 16: Weekly buckle rod
One and 13 new points; Asia:
Part Office: Entrustment
Part 1: Is a position element,
This 3/178
Car Department 373.1-133 issued a continuous year 4 type guide 19
Standard name is with guide design.
GB/T 457↓,4-2003
As the standard of the three-compilation agent for the wide teaching people to add! "Integration" because \ and "rule of thumb" and "half-specification" are determined by you! . There is content.
Cover changes to the size of the secret system such as size specifications or materials to recommend the storage of the project
Change the request,
Please contact the request,
Rate surface trend of the original standard pool of life sharing,
Not part of the electrical union proposed,
This part only contains one pressure proposed by the Standardization Technical Committee SAC/TC3) one point order unit: Shanghai Jiao Erge also has zero production Co., Ltd., Lifting Air Products Factory Lin Ding Station Science and Technology Research Institute, Ertuan Science and Technology Company, Xinxing Guangyu Industrial Company
World Want to hit people Zhang Baojin has history Zhen, code, come to the group Yang Ling, tea, hand beauty. 1 Signed on September 9, 19x4, 2C3: First contract, GB/T 4678.4-003
1 Scope
Die casting parts Part 4: Shoulder guide pins
This part specifies the size specifications and tolerances of guide pins for die casting. This part is applicable to guide pins and push plate guide pins for die casting. This part gives the material guide and convenience requirements, and specifies the marking of shoulder guide pins. 2 Normative references
The clauses in the following documents become clauses of this part through reference in this part of H468. For any old dated referenced document, all subsequent versions (excluding errors) or waiting versions shall not apply to this part. However, the latest versions of these documents shall apply to any undated referenced document. Technical conditions for pressed mould parts GB/T 4679-2003 Dimensional specifications See Figure 1 and Table 1. Surface coverage is in meters. Note: Surface integrity Ra-5.3/m: Unadjusted mm×45° Can be increased or filled with oil grooves. The center holes at both ends are allowed to be retained.
Figure 1 Guide column with shoulder
Table 1 Dimensions of guide column with shoulder
GB/T 4678.4—2003
Unit: meter
GR/T 4678.4m70C3bzxz.net
Material and source material are selected by the manufacturer, recommended 119AGCr5 inverter 50 HRC--56 HR. Technical requirements The material should be in accordance with the provisions of GT4379, 2003. According to this part, the strip should have the following markings: a) The strip should be marked with the following markings: The strip diameter D is in meters: The strip length is 1 meter, (B4678.42C03, 1=15mm, L=63m, L,-25, and the strip shoulder should be marked as follows: 5X53:3GB/T67A.1—2003
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.