GB/T 5386-1994 Motorcycle and moped coasting test method

This standard specifies the test conditions and test methods for coasting tests on motorcycles and mopeds. This standard applies to coasting tests on motorcycles and mopeds (except racing motorcycles), but not to coasting tests on motorcycles and mopeds with continuously variable transmission, automatic transmission and automatic clutch. GB/T 5386-1994 Coasting test method for motorcycles and mopeds GB/T5386-1994 Standard download decompression password: www.bzxz.net

National Standard of the People's Republic of China
Method of coasting test for
motorcycles and mopeds
Subject content and scope of application
This standard specifies the test conditions and test methods for coasting test for motorcycles and mopeds. GB/T 5386-94
GB 4564--84
GB 5386—85
This standard applies to coasting test for motorcycles and mopeds (except racing cars), but does not apply to coasting test for motorcycles and mopeds with continuously variable transmission, automatic transmission and automatic clutch. 2 Referenced standards
GB/T5378 General principles for road test of motorcycles and mopeds 3 Test conditions
The test conditions and preparation of the test vehicle shall comply with the provisions of GB/T5378. 4 Test method
4.1 Determination of gliding distance
4.1.1 Select a sufficiently long gliding area and auxiliary driving area on the test road. 4.1.2 The initial gliding speed for motorcycles is stipulated to be 40 ± 1 km/h; for mopeds, it is stipulated to be 30 ± 1 km/h. 4.1.3 When the test vehicle enters the starting point of the deceleration test area, the clutch should be disengaged and the gear should be in neutral, and the engine may not be turned off. 4.1.4 Measure the distance from the starting point to the stopping point of the test vehicle. 4.2 Determination of gliding resistance coefficient
4.2.1 Set up the gliding test area and each test section on the test road according to the diagram, and set up a timing device at each point. Auxiliary driving area
Initial speed test section
50m Deceleration test section
Test point
Test point
Test point
50 m Deceleration test section
Test point
Initial speed test section
Note: If a test instrument with an automatic recording device is used for testing, a specific test section may not be set up on the test section. Approved by the State Administration of Technical Supervision on December 27, 1994 156
Auxiliary driving area
Implementation on July 1, 1995
GB/T 5386—94
4.2.2 The initial coasting speed shall ensure that the time for the vehicle under test to pass the 100m test section is within 20±2s. 4.2.3 When the vehicle under test enters the starting point of the deceleration test section, the clutch shall be disengaged and the gear shall be in neutral, and the engine may not be turned off. 4.2.4 Measure the actual initial taxiing speed and the taxiing time t1 and t2 of the test vehicle passing through the 50m and 100m test sections. 4.2.5 Calculate the taxiing deceleration and taxiing resistance coefficient based on the measured values ​​using formulas (1) and (2). b =
In formulas (1) and (2):
Sliding deceleration, m/s2
t2 - t/
t1—time from the starting point to the 50m test point, st2—time from the starting point to the 100m test point, s; f—sliding resistance coefficient.
4.3 Test results
4.3.1 The taxiing test is carried out twice, one round trip as one time, the taxiing distance is the larger value of the arithmetic mean of the forward and reverse distances, and the taxiing resistance coefficient is the smaller value of the arithmetic mean of the forward and reverse distances. 4.3.2 The test data and results shall be recorded in the table of Appendix A (Supplement). 157
Vehicle model
Frame number
Engine number
Vehicle curb weight
Relative humidity
Front wheel air pressure
Driver
Test sequence
Driving direction
GB/T5386—94
Appendix Awww.bzxz.net
Sliding test record
(Supplement)||t t||Test date
Test location
kgDriver mass
%Atmospheric pressure
kPaRear wheel pressure
Sliding distance test
Actual sliding
Initial velocity
Sliding distance
Additional remarks:
Sliding distance
Average value of measured values
This standard is proposed by China Aviation Industry Corporation. Tester
Side wheel pressure
Sliding drag coefficient test
Actual sliding
Initial velocity
Pass deceleration test
Interval time, s
Sliding drag coefficient
This standard is under the jurisdiction of the National Technical Committee for Automobile Standardization. This standard was drafted by Nanchang Aircraft Manufacturing Company. The main drafters of this standard are Xu Xisheng, Xu Youqing, You Bingliang and Wang Zhen. 158
Deceleration
Average value of measured value
Sliding resistance
Force coefficient
Liu Bei Note
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.