JB/T 2523.2-1999 Floor Lathe Parameters

JB/T 2523.2-1999 JB/T 2523.2-1999 Floor Lathe Parameters JB/T2523.2-1999 Standard Download Decompression Password: www.bzxz.net

ICS25.080.10
Machinery Industry Standard of the People's Republic of China
JB/T2523.2—1999
Floor-type lathe
Published on 1999-05-20
National Bureau of Machinery Industry
Implementation on 2000-01-01
JB/T2523.2—1999
This standard is a revision of JB252379 "Floor-type lathe day parameters". During the revision, only editorial modifications were made in accordance with relevant regulations, and the technical content remained unchanged. bzxz.net
"Floor-type lathe" series of standards, which includes the following four parts: This standard is JB/T2523
JB/T2523.1—1997
JB/T2523.2—1999
JB/T2523.3—1999
JB/T 2523.41999
Technical conditions for floor-type lathes
Floor-type lathes
Floor-type lathes
Series spectrum
Precision inspection
This standard replaces JB2523—79 from the date of implementation. This standard is proposed by the National Technical Committee for Metal Cutting Machine Tools Standardization. This standard is under the jurisdiction of the Heavy Machine Tool Branch of the National Technical Committee for Metal Cutting Machine Tools Standardization. This standard was drafted by: Qiqihar No. 1 Machine Tool Factory and Qinghai Heavy Machine Tool Factory. This standard was first issued in March 1979.
1 Scope
Machinery Industry Standard of the People's Republic of China
Floor-type lathe
This standard specifies the parameters of floor-type lathes. JB/T2523.2-1999
Replaces JB2523.2-79
This standard applies to new-design floor-type lathes for general use with a maximum workpiece rotation diameter of 1600-8000mm in the pit and a maximum workpiece length of 2000-4000mm between the centers. It also applies to floor-type lathes for general use without pits. 2 Parameters
The type of floor-type lathe is shown in Figure 1. The parameters of the machine tool should comply with the provisions of Table 1. Figure 1
Floor-type lathe
Floor-type lathe parameters
Maximum workpiece rotation diameter D in the pit
Maximum workpiece length
Maximum workpiece weight
Center spacing 1
L in the pit
Suspension clamp m, 2)
Top clamp m2
1) Refers to the distance between the front and rear centers when the tailstock is in the last position on the base plate and the tailstock center extends to the maximum allowable length. If there are special requirements for L, it can be increased by 2000mm, but the maximum length shall not exceed 16000mm, which shall be agreed upon by the user and the manufacturer. 2) m refers to the maximum weight of the suspended workpiece when the distance from the center of gravity of the workpiece to the end face of the faceplate is half of L (for Φ1600mm and Φ2000mm machine tools, m refers to the maximum weight of the suspended workpiece when the distance from the center of gravity of the workpiece to the end face of the faceplate is 250mm and 320mm respectively) Approved by the State Machinery Industry Bureau on May 20, 1999 and implemented on January 1, 2000
Machinery Industry Standards
Floor-type Lathe Parameters
JB/T2523.2—1999| |tt||Published by the Machinery Standardization Research Institute of the Ministry of Machinery Industry Printed by the Machinery Standardization Research Institute of the Ministry of Machinery Industry (No. 2, Shouti South Road, Beijing: Postal Code 100044)*
1/16 Printing Sheet 1/4 Words 4000
Format 880×1230
First Printing in July 1999
First Edition in July 1999
Print Quantity 1-500
Price 500 Yuan
99-192
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.