JB/T 2648.1-1995 Main shapes and basic dimensions of blades for bulldozers, scrapers and graders

This standard specifies the main cross-section shapes and basic dimensions of blades for bulldozers, scrapers and motor graders, the positions of mounting bolt holes, and the shapes and dimensions of the holes. The blade dimensions used take into account the requirements for interchangeability. This standard applies to bulldozers, scrapers and motor graders as defined in GB 8498. JB/T 2648.1-1995 Main shapes and basic dimensions of blades for bulldozers, scrapers and motor graders JB/T2648.1-1995 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T2648.1
Mi Yi Ke
1995-06-20
JB/T2648.11995bzxZ.net
This mechanical industry standard for blades and bolts for bulldozers, scrapers and graders includes the following parts: Part 1 (i.e. JB/T2648.1): J The main shapes and basic dimensions of blades: Part 2 (i.e. JB/『2648.2): Technical requirements for blades: Part 3 (i.e. JI3/『2648.3): The standard for bolts for blades Part 1 is formulated based on the international standard ISO71291989 "Upper machinery - Pushers, transporters and graders - Blades: Three main shapes and basic dimensions" drafted by the International Organization for Standardization IS0/TC127 Earthmoving Machinery Technical Committee. The technical content is equivalent to this international standard.
Part 3 of the standard, the section on the shape and dimensions of the screw rod for blades is formulated based on the international standard ISO71291989 "Upper machinery - Pushers, transporters and graders - Blades: Three main shapes and basic dimensions" drafted by the International Organization for Standardization IS0/TC127 Earthmoving Machinery Technical Committee. The technical content is equivalent to this international standard. Appendix A in Part 3 is the standard appendix. This standard shall be implemented from January 1, 1996, and replace JB2648-81. This standard was proposed by Tianjin Engineering Machinery Research Institute of the Ministry of Machinery Industry and is under the jurisdiction of the Ministry of Machinery Industry. Part 1 and Part 2 of this standard were drafted by Tianjin Engineering Machinery Research Institute of the Ministry of Machinery Industry; Part 3 of this standard was jointly drafted by Tianjin Engineering Machinery Research Institute of the Ministry of Machinery Industry and Shenyang Screw Factory. The main drafters of this standard are Wu Runcai, Yang Yuyi, and Shenyang Screw Factory. 1 Scope JB/T2648.1 This standard specifies the main cross-sectional shape and basic dimensions of blades for bulldozers, scrapers and flatbed trucks, the position of the mounting screw holes, and the shape and dimensions of the holes. The blade size adopted takes into account the interdependence requirements. This standard applies to bulldozers, scrapers and graders defined by GFB8498. 2 Reference standards
The clauses contained in the following standards constitute non-standard clauses through reference in this standard. When the non-standard is published, the versions shown in the following standards are valid. All standards will be revised. Parties using this standard should explore the possibility of using the latest version of the following standards. GB 8198-87 Mechanical Basic Types 3 Main shapes and basic dimensions of the cross-section of the blade The main shapes and basic dimensions of the cross-section of the blade shall comply with the provisions of Table 1 and Table 2. 4 Position of mounting bolt holes
4.1 The positions of mounting bolt holes are listed in Tables 3 and 4. 4.2 The position tolerance of each tapered countersunk hole shall not exceed 3.2 mml. 4.3 The straightness tolerance of the blade shall not exceed 2 mm/ml. 5 Shape and size of mounting bolt holes
5.1 The shape and size of mounting bolt holes are listed in Table 5. 5.2 The tolerance of the inscribed circle of the square hole and the conical countersunk hole shall not exceed 0.8 mm1 Table 1, bulldozer and scraper
Applicable (for reference only)
Bulldozer
Scraper
Width W
Nominal
1995-06-20
Thickness!
Nominal size
13(12.7)1:
Example Angle end F
1996-01-01 Small lock
Illegal (for reference only)
Pusher
Scraper
Width W
Nominal ruler
JB/T2648.1
Table 1 continued)
Thickness
Nominal size
23(25. 4)
28(78.6)13
28(28.6)\)
25(23.4)3
28(28.6.,1
25(23.4))
Except the front parts
H estimated quality
Example angle end F
Applicable (for reference only)
Bulldozer
Scraper
Nominal size
Note, “×” is applicable to the machine.
Width certificate
Nominal ruler
Instructions for use:
JB/T2648.11995
Table 1 (end)
Thickness T
Nominal size
28(28. 6:
Table trim machine
Thickness T
Nominal ruler:
20(19)11
Except for parts
Other materials
Nominal size
Chamfered end F
F minimum
1The value on the left of the bracket is the thickness of the plate in my country when it is manufactured using plate material other than IS0 7129 Standard, adopt A, sheet rolling profile when controlling the value in brackets. 3
Sub center line -
JB/T2648.11995
Table 3 Push ten machine and scraper
Hole plate position
Middle part should be P
Hole at the center line
Both ends Q\
Note, 1) For small machines, the instantaneous
JB/ T2648.1
Table 4 Grader
Nominal inch
271905
Distance from edge
Nominal foot
Nominal foot
Reverse taper hole
Nominal end size
Bolt reference book diameter
JB/T2648.1||tt| |Screw hole for installation
31°up 2
;When the effective stop is H, the cone
head hole or the first diameter of the hole
, square
: minimum effective thickness
120:10
reverse hole
R: circle radius of the hole
A: diagonal size of the square hole
F: square surface sink
samico
xiaoganmelancholy
100044
lying880b1230
for section 3/4
square 14,000
1996nest1cabinwheeldaisu
1996table1antelope
square 1
pengxianjikeycobalt
brain10.00wing
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.