CB/T 3317-2001 Basic parameters and installation connection dimensions of marine plunger hydraulic cylinders

CB/T 3317-2001 Basic parameters and installation connection dimensions of marine plunger hydraulic cylinders CB/T3317-2001 standard download decompression password: www.bzxz.net

ICS47.020.30
Registration number: 9831-2002
Ship industry standard of the People's Republic of China
CB/T3317-2001
Replace CB*3005-85.CB*3317-87
Basic parameter and mounting connection of marine plunger hydraulic cylinder
and installation connection size
Basic parameter and mounting connection 2001-1115 Issued
Issued by the National Defense Science, Technology and Industry Commission
2002-02-01 Implementation
CB/T3317-2001
This standard is a revision of CB*3005-85 "Basic parameters of marine plunger type hydraulic cylinders" and CB*3317-87 "Installation form and connection dimensions of marine plunger type hydraulic cylinders", merging the two standards into one standard to make the standard more reasonable and convenient to use. In the revision process, the latest versions of international and national standards are cited as much as possible. Spherical bearings are selected according to the external dimensions of radial spherical bearings in GB/T9163-1990.
From the date of implementation of this standard, it will replace CB*3005-85 and CB*3317-87 at the same time. This standard is proposed and managed by the Hydraulic and Pneumatic Subcommittee of the National Technical Committee for Standardization of Marine Machinery. The drafting units of this standard are: China Shipbuilding Industry Comprehensive Technology and Economic Research Institute, Chongqing Hydraulic Parts Factory. The main drafters of this standard are: Cai Zhenzhong, Zeng Ersheng. This standard was first issued (trial implementation) in 1977 and revised in 1985 and 1987. 1 Scope
CB/T3317-2001
Basic parameters of marine plunger hydraulic cylinders
and installation connection dimensions
This standard specifies the basic parameters and installation connection dimensions of marine plunger hydraulic cylinders. This standard is applicable to marine plunger hydraulic cylinders (hereinafter referred to as cylinders) that use mineral-based hydraulic fluid as the working medium and perform reciprocating linear motion. 2
Cited standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid.
All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T321-1980
GB/T9163-1990
Basic parameters
3.1 Nominal pressure
Priority number and priority number system
Dimensions of radial spherical plain bearings
The nominal pressure of the cylinder is 16MPa and 25MPa. Plunger diameter
The plunger diameter of the cylinder is 100mm, 125mm, 160mm, 200mm, 250mm, 320mm, etc. 3.3
Plunger stroke
The plunger stroke of the earring type cylinder is selected according to Table 1. Table 1
The plunger stroke of the 25MPa series cylinder is selected according to the "O" symbol in the bold frame. Note 1: 2
Note 2:
When the stroke cannot meet the requirements, it can be selected according to the R10 numerical system in GB/T321, but the last digit is 0 or 5. 250
CB/T3317-2001
3.3.2 The plunger stroke of the internal ball head type cylinder is determined according to Table 2. Table 2
Inlet and outlet oil port dimensions, installation type and connection dimensions of the cylinder 4
4.1 Inlet and outlet oil port dimensions of the cylinder
Plunger diameter
4.1.1 The inlet and outlet oil port dimensions of the earring type cylinder shall be determined according to Figure 1 and Table 3L
Nominal pressure
16MPa, 25MPa
Plunger diameter
Oil port diameter
M33×2
M42×2
M50×2
M60×2
56.0±0.4
73.0±0.4
Note: Plunger diameter 100
Cylinders with a diameter of 320mm are only suitable for flange connection oil ports. Cylinders with diameters of mm to 125m are only suitable for internal threaded oil ports. 2
CB/T3317-2001
4.1.2 The inlet and outlet dimensions of the internal ball head mounted cylinders shall be in accordance with Figure 2 and Table 4. @
Nominal pressure
Plunger diameter
Oil port diameter
Installation type and connection dimensions of cylinders
16MPa The plunger end threaded connection dimensions of the cylinder are shown in Table 5. Table 5
Plunger diameter
Thread diameter
M42×2
M48×2
M64×3
M80×3
M100×3
M125×4
4.2.2 The plunger end threaded connection dimensions of the cylinder with diameters of 25MPa are shown in Table 6. Table 6
Plunger diameter
Thread diameter
M64×3
M100×3
M125X4
M160×4
16 MPa
Thread length
Thread length
4.3 Double clevis installation type and connection dimensions
The double clevis installation type with bushing is shown in Figure 3.
a) Piston rod end with bushing earringwww.bzxz.net
CB/T3317-2001
MPa The connection dimensions of cylinder with bushing double earring are shown in Table 7. 16
Plunger diameter
MPa The connection dimensions of cylinder with bushing double earring are shown in Table 8. 25
Plunger diameter
Installation type and connection dimensions of double earring with spherical bearing 4.4
Installation type of double earring with spherical bearing is shown in Figure 4. L
b) Cylinder head end with sleeve earrings
M42×2
M48×2
M64×3
M80×3
M100X3
M125×4
M48×2
M80×3
M100×3
M125×4
M160×4
a) Plunger rod end spherical bearing earrings
CB/T3317-2001
16MPa Cylinder with spherical bearing double earrings connection dimensions are shown in Table 9. Table 9
Plunger diameter
MPaCylinder with spherical bearing double earring connection dimensions are shown in Table 10.25
Plunger diameter
Spherical bearing with spherical bearing earring connection is selected according to GB/T9163. 4.5Inner ball head installation type and connection dimensions
16MPaInner ball head installation type is shown in Figure 5.
b) Cylinder head spherical bearing earrings
M42×3
M48×3
M80×3
M100×3
M125×4
M48×3
M80×3
M100×3
M125X4
M160X4
CB/T3317-2001
216MPa cylinder plunger end connection dimensions are shown in Table 11. 4.5.2
Plunger diameter
4.5.316MPa internal ball head installation type cylinder bottom installation type is shown in Figure 6. Figure 6
16MPa internal ball head installation type cylinder base connection dimensions are according to Table 12. Table 12
Plunger diameter
*Caolu Yiwei* provides high-quality documents. If the documents you downloaded are missing pages, blurred, etc., or you encounter scarce files that cannot be found, please send a message to me! I will definitely help you solve it! I have more than 200,000 domestic and foreign standards, including a full range of GB national standards and domestic industry and department standards, a full range of BSIEN
SSPC ANSI
AASHTO
TBR RCC national classification societies and many other international standards. Docin download website: http://www.docin.com/liuyx866
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.