HG 20604-1997 Pressure-temperature grades for steel pipe flanges (European system)

This standard specifies the maximum non-impact working pressure of steel pipe flanges (European system) at 1_ working temperature. This standard applies to steel pipe flanges and flange covers specified in HG 20592. HG 20604-1997 Pressure-Temperature Grades for Steel Pipe Flanges (European System) HG20604-1997 Standard download decompression password: www.bzxz.net

Steel pipe flange pressure-temperature grade
(European system)
HG20604-97
1 Question content and scope of application
This standard specifies the maximum non-impact working pressure of steel pipe flanges (European system) at working temperature. This standard applies to steel pipe flanges and flange covers specified in HG20592. 153
HG20592
HG20603
Reference Standard
《Steel Pipe Flange Type, Parameters (European System)》Steel Pipe Flange Technical Specifications (European System)》3 Maximum Non-impact Working Pressure
The maximum non-impact working pressure of steel pipe flanges and flange covers with nominal pressure PN of 0.25MPa (2.5har) ~ 25.0MPa (250har) at working temperature shall be in accordance with the provisions of Table 3.0.1-1~10. At intermediate temperatures, the interpolation method is used to determine. The flange material categories listed in Table 3.0.11~-10 are in accordance with the provisions of HG20603. The maximum non-impact working pressure value of ferritic steel at 100℃ in the table can be used up to 120℃, and the maximum non-impact working pressure value of austenitic stainless steel at 20℃ can be used up to 50.
.3.0.2 The working temperature refers to the temperature of the flange metal under pressure. When the working temperature is lower than 20℃, the maximum non-impact working pressure of the flange is the same as that at 20℃.
3.0.3 If the two flanges on a flange joint have different pressure ratings, the maximum non-impact working pressure of the joint shall be the lower value, and the stud torque during installation shall be controlled to prevent over-tightening. 3.0.4 When the working temperature is higher than the listed temperature and there is no exact (rated) value, it can be determined by the designer based on usage experience or calculation.
3.0.5 When using materials other than those listed in the table, the maximum non-impact positive working pressure of the flange can be determined based on the principle of equivalent allowable stress of the material and the material science listed in the table, but it shall not be greater than the nominal pressure. 155
9800002+015095090
9802060
2h *060z5'099*069\
090109009009009009009*009*0
/090090 09009:0
222808050999
822162228026050905025009009009 0909009025065*009 *009 0
[020800
2+08+*015*009*009*0
9102018210981026103120890
106198119022018022
101111011||t t||61101981222
19'093'009 0-105
92*092*0530
920980530
19-0500
520920
51188121
3800521
[52102\0
5t*0521'03'0
98't ST
G1'9z'1
96 *0 1 66 080 *1
281681801
68*036°℃
96*0[121'1
28098:0
880821126271
809*00208*0
s1t62'1187't
26 *0 G0 -1
OWS'(:g
82t#v29-12919*
88*2t1
zt8'++'t
29 *069 *bZxz.net
2-082-0
09-02909049*0
128*036'0
S8'0↓v6\
15*0990. 190
28028 0
9600*1
Towe'0.os||tt ||1aws '0-1
L00103
35-1921
25-196802
1852's0't
2226251
982!26
181*11 981
68260163
+*60'0
0'o1'01o'o1001
ows0 -9
1o'o1o'o1: 0'o1
[o'oto'o1
o'o1*o1
SGo*01||t t||oo10'o1
0'o10'010'o1owg'0--o1
0'o1001
+2-98#'s
1621's
[1+*+ - 62*-
661219
8*91os-+0
owl-/2
8\9'0-101
2F* i 58ot 's
1o11001
8'810-02
12-12+52052
0\912'91821981
0's1+'s11*91
1'6212+*53
6161051
t-9 1+-21
6+'s1+**1
21910811082
0-9052
05205090505052050105
0*92 1097
0052001
8*228-8
'118'et51
0'520*52
5*192*9191-21
2*612020*1
0S100108
|tt||1116*119zt9\t0's10-91
2'121]
z*t1*1
e'otz'116'lt6'z1
3168161
+'ol't!
9-10-91
0-91 0*910*9toWs 0-+39
0-910'910*910*90*9
091091n91ow1 --+/1z
z*1/9'1/0'9[
+0*91 10*910*91
2*5110'91/0-910'91
o'910*9u*91
2*s10'910'91
ez10'e1+'et
Additional remarks: Proposer, editor and main drafter of this standard Proposer: Equipment Design Technology Center Station, Ministry of Chemical Industry Chemical Process Piping Design Technology Center Station, Ministry of Chemical Industry Editor: Equipment Design Technology Center Station, Ministry of Chemical Industry Main drafter: Ying Daoyan Yu Jun
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.