JB/T 5096-1991 Technical requirements for bonding process of paper oil filter elements for internal combustion engines

This standard specifies the technical requirements and bonding process for paper oil filter elements for internal combustion engines. This standard is applicable to the bonding between filter paper and metal end caps of paper oil filter elements for small and medium power internal combustion engines. JB/T 5096-1991 Technical requirements for bonding process of paper oil filter elements for internal combustion engines JB/T5096-1991 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T5096-91
Bonding Technology of Paper Oil Filter Element for Internal Combustion Engine
Technical Conditions
Published on 1991-07-01
Published by the Ministry of Machinery and Electronics Industry of the People's Republic of China
Implemented on 1992-07-01
Mechanical Industry Standard of the People's Republic of China
Bonding Technology of Paper Oil Filter Element for Internal Combustion Engine
Technical Conditions
1 Subject Content and Applicable Scope
This standard specifies the technical requirements and bonding process flow of bonding of paper oil filter element for internal combustion engine. This standard is applicable to the bonding between filter paper and end cover of paper oil filter element for small and medium power internal combustion engine. 2 Reference standards
JB/T5098 Technical conditions for adhesives for paper oil filters for internal combustion engines 3 Technical requirements
3.1 The adhesive surface of the filter end cover should be cleaned, dried and other surface treatments. JB/T5096-91
3.2 The adhesive should comply with the provisions of JB/T5098. 3.3 The proportion of two-component adhesives should be strictly formulated in accordance with the provisions of its instruction manual. If fillers need to be added, the fillers must be dried and sieved to remove particles with a diameter greater than 0.6mm. 3.4 The single-component adhesive should be fully stirred before use (a small amount of diluent can be added when necessary, such as a small amount of kerosene as a diluent for polyvinyl chloride resin adhesives) to reduce its viscosity to an appropriate level. 3.5 The room temperature adhesive should be used within 20~120min after mixing. 3.6 After the adhesive is injected into the end cover, it should be evenly distributed in the end cover. 3.7 After the solvent-containing adhesive is injected into the end cap, it must be air-dried. The exposure time should be determined according to the instructions for use and the temperature and ventilation conditions during bonding.
3.8 After the paper core is inserted into the end cap, it should be placed flat and a little pressure should be applied to its top. The relative position of the filter paper and the end cap should not be changed before the adhesive is cured.
3.9 The curing temperature and time of the adhesive should be determined according to the instructions for use and the size of the filter element. The preparation and curing conditions of several commonly used paper oil filter element adhesives are shown in Appendix A (reference). Gluing process flow chart
One-component adhesive
Two-component adhesive
1991-07-01 approved by the Ministry of Machinery and Electronics Industry for injection
Component A
Component B
1992-07-01 implementation
KH-Laz
Additional instructions:
JB/T509691| |tt||Mixture and curing of several commonly used paper oil filter adhesives (reference parts)
405-1+405-2: Filler
1-2:2~6
Single component
Single component
Curing temperature
185±5℃
20~80℃
Curing timebzxZ.net
3~5 min
10~240min
This standard was proposed and managed by the Shanghai Internal Combustion Engine Research Institute of the Ministry of Machinery and Electronics Industry. This standard was drafted by the Shanghai Internal Combustion Engine Research Institute of the Ministry of Machinery and Electronics Industry. The main drafters of this standard are Liu Jialin, Yang Jieru and Fin Qizhen. The inner surface of the end cap should be clean and dry, without oil or dust. The inner surface of the end cap should be clean and dry, without oil or dust.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.