
JB/T 10119-1999 Machine tool fixture parts and components retaining rings
time:
2024-08-12 02:15:37
- JB/T 10119-1999
- in force
Standard ID:
JB/T 10119-1999
Standard Name:
Machine tool fixture parts and components retaining rings
Chinese Name:
机床夹具零件及部件 卡环
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
Original standard number GB/T 12884-1991

Skip to download
Summary:
JB/T 10118-1999 JB/T 10119-1999 Machine tool fixture parts and components retaining ring JB/T10119-1999 Standard download decompression password: www.bzxz.net

Some standard content:
IC5 28.060.41
Mechanical Industry Standard of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06Promulgated
State Machinery Industry Bureau
Implementation on 2000-01-01
Mechanical Industry Standard of the People's Republic of China
Parts and components of jigs and fixtures for machine tools
llk'paris and units ufjigswud rixturesSnapringwwW.bzxz.Net
This standard specifies the snap rings suitable for parts with a diameter of 5~12mm. The sizes are shown in the table below.
Approved by the State Machinery Industry Bureau on September 6, 1999
JBT09-
Implementation of 2000-01-U1
Nominal diameter
[Applicable, allowable point diameter]
>10~15
>20~25
>25 ~ 32
>32 -6
> G: ~ 1
> 50 60
>7g ~80
> 80 90
> 9 -- 1
100~1u
>110-115
3 Marking
3.1 Marking example:
Snap ring with nominal diameter of 10~[5:
Snap ring 10-15JB/T10119—1999
JB10119—1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Mechanical Industry Standard of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06Promulgated
State Machinery Industry Bureau
Implementation on 2000-01-01
Mechanical Industry Standard of the People's Republic of China
Parts and components of jigs and fixtures for machine tools
llk'paris and units ufjigswud rixturesSnapringwwW.bzxz.Net
This standard specifies the snap rings suitable for parts with a diameter of 5~12mm. The sizes are shown in the table below.
Approved by the State Machinery Industry Bureau on September 6, 1999
JBT09-
Implementation of 2000-01-U1
Nominal diameter
[Applicable, allowable point diameter]
>10~15
>20~25
>25 ~ 32
>32 -6
> G: ~ 1
> 50 60
>7g ~80
> 80 90
> 9 -- 1
100~1u
>110-115
3 Marking
3.1 Marking example:
Snap ring with nominal diameter of 10~[5:
Snap ring 10-15JB/T10119—1999
JB10119—1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- GB 4706.43-1999 Safety of household and similar electrical appliances Particular requirements for projectors and similar appliances
- GB/T 15773-1995 Regulation of acceptance for comprehensive control of soil erosion
- GB/T 3291.1-1997 Textiles - Textile materials properties and test terms - Part 1: Fibres and yarns
- GB/T 8484-2002 Classification and testing methods for thermal insulation performance of building exterior windows
- GB/T 3668.12-1983 Dimensions of floor-standing columns with guide rails for common components of modular machine tools
- JB/T 10040-2001 Diamond dressing roller
- HG/T 20701.3-2000 Working procedures for the professional engineering design phase of containers and heat exchangers
- GB 16483-2000 Provisions for the preparation of chemical safety data sheets
- GB 9178-1988 Integrated Circuit Terminology
- JB/T 7966.5-1999 Die milling cutters Part 5: Flattened straight shank conical end mills
- JB/T 6315-1992 Steam turbine welding procedure qualification
- GB 50155-1992 Terminology standard for heating, ventilation and air conditioning
- GB/T 13474-1992 The method of editing tidal tables and tidal stream charts for ship
- JB/T 7374-1994 Technical requirements for pneumatic air filters
- GB/T 4026-2004 Basic methods and safety rules for marking human-machine interfaces - General rules for the application of equipment terminals and specific conductor terminal marking and alphanumeric systems
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail:bzxznet@163.com