GB/T 14854.2-1993 Performance requirements for broadcast video tapes
time:
2024-08-09 05:29:11
- GB/T 14854.2-1993
- in force
Standard ID:
GB/T 14854.2-1993
Standard Name:
Performance requirements for broadcast video tapes
Chinese Name:
广播录像磁带性能要求
Standard category:
National Standard (GB)
-
Date of Release:
1993-01-02 -
Date of Implementation:
1994-09-01
Standard ICS number:
Telecommunications, audio and video technology>>Audio, video and audiovisual engineering>>33.160.40 Video systemsChina Standard Classification Number:
Chemicals>>Information Chemicals>>G83 Magnetic Recording Materials
Release date:
1993-12-30Review date:
2004-10-14Drafter:
Chen ChengquanDrafting Organization:
Standardization Planning Institute of the Ministry of Radio, Film and TelevisionFocal point Organization:
National Radio and Television Standardization Technical CommitteeProposing Organization:
Radio, Film and Television DepartmentPublishing Department:
State Bureau of Technical SupervisionCompetent Authority:
State Administration of Radio, Film and Television
Description (Translated English) / downloadSkip to download
Summary:
This standard specifies the performance of video tapes for broadcasting. This standard applies to video tapes with a width of 25.4 mm and 19.00 mm. GB/T 14854.2-1993 Performance requirements for broadcast video tapes GB/T14854.2-1993 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
National Standard of the People's Republic of China
Characteristic requirements for broadcast video tape
Characteristic requirements for broadcast video tape 1 Subject content and applicable scope
This standard specifies the performance of broadcast video tapes. This standard applies to video tapes with a width of 25.4 mm and 19.00 mm. Performance requirements for broadcast video tapes
The performance requirements for broadcast video tapes are shown in Table 1. Table 1
4. Residual elongation
5. Interlayer adhesion
6. Transverse bending deformation
Longitudinal bending deformation
8. Surface voltage
9. Optimum video current ratio
10. RF playback output, sensitivity
11. RF playback output sensitivity non-uniformity
12. Image brightness signal-to-noise ratio
13. Image chromaticity signal-to-noise ratiowwW.bzxz.Net
14. Dropout
15. Stop image characteristics
Approved by the State Technical Supervision Bureau on December 30, 1993Magnetic layer
pieces/minute
GB/T 14854.2—93
25.4mm tape
25.4+8.10
See Table 2
1000000
19. 00mm tape
19.00+0.03
See Table 2
Implemented on September 1, 1994
16. Sound relative sensitivity*
17. Sound relative sensitivity non-uniformity
18. Sound amplitude-frequency characteristics*
19. Sound distortion
20. Sound signal-to-noise ratio
21. Copy effect
22. Demagnetization degree
GB/T 14854.2--93
Continued Table 1
25.4nmim tape
19.00mtm tape
The * in the table is compared with the reference value of the reference tape. This standard stipulates that the group average value in the sampling of this model of products shall be taken as the reference. The absolute value of the signal-to-noise ratio of ear brightness and chromaticity (including amplitude modulation and phase modulation) shall not be less than 46dB for 25.4mm tape and shall not be less than 47dB for 19.00mm tape. Table 2
Nominal recording time, min
Additional instructions:
This standard is proposed by the Ministry of Radio, Film and Television
25.4mm tape
This standard is drafted by the Standardization Planning Institute of the Ministry of Radio, Film and Television. The main drafter of this standard is Chen Chengquan
Degree, m
19.00mm tape
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Characteristic requirements for broadcast video tape
Characteristic requirements for broadcast video tape 1 Subject content and applicable scope
This standard specifies the performance of broadcast video tapes. This standard applies to video tapes with a width of 25.4 mm and 19.00 mm. Performance requirements for broadcast video tapes
The performance requirements for broadcast video tapes are shown in Table 1. Table 1
4. Residual elongation
5. Interlayer adhesion
6. Transverse bending deformation
Longitudinal bending deformation
8. Surface voltage
9. Optimum video current ratio
10. RF playback output, sensitivity
11. RF playback output sensitivity non-uniformity
12. Image brightness signal-to-noise ratio
13. Image chromaticity signal-to-noise ratiowwW.bzxz.Net
14. Dropout
15. Stop image characteristics
Approved by the State Technical Supervision Bureau on December 30, 1993Magnetic layer
pieces/minute
GB/T 14854.2—93
25.4mm tape
25.4+8.10
See Table 2
1000000
19. 00mm tape
19.00+0.03
See Table 2
Implemented on September 1, 1994
16. Sound relative sensitivity*
17. Sound relative sensitivity non-uniformity
18. Sound amplitude-frequency characteristics*
19. Sound distortion
20. Sound signal-to-noise ratio
21. Copy effect
22. Demagnetization degree
GB/T 14854.2--93
Continued Table 1
25.4nmim tape
19.00mtm tape
The * in the table is compared with the reference value of the reference tape. This standard stipulates that the group average value in the sampling of this model of products shall be taken as the reference. The absolute value of the signal-to-noise ratio of ear brightness and chromaticity (including amplitude modulation and phase modulation) shall not be less than 46dB for 25.4mm tape and shall not be less than 47dB for 19.00mm tape. Table 2
Nominal recording time, min
Additional instructions:
This standard is proposed by the Ministry of Radio, Film and Television
25.4mm tape
This standard is drafted by the Standardization Planning Institute of the Ministry of Radio, Film and Television. The main drafter of this standard is Chen Chengquan
Degree, m
19.00mm tape
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- JB/T 8018.3-1999 Machine tool fixture parts and components adjustment V-blocks
- HG/T 20701.1-2000 Scope of professional responsibilities for vessels and heat exchangers and tasks at each stage of design
- JG/T 24-2000 Synthetic resin emulsion sand wall building paint JG/T24-2000
- GB/T 14926.15-2001 Detection method of Streptococcus pneumoniae in experimental animals
- GB/T 14674-1993 Analytical method for iodine-131 in milk
- GB 11575-1989 Basic quotas for equipment for marine transport vessel repair
- GB/T 18131-2000 STANDARD shipping marks for international trade
- GB/T 2820.10-2002 Reciprocating internal combustion engine driven alternating current generating sets Part 10: Measurement of noise (envelope method)
- GB/T 2424.19-1984 Basic environmental testing procedures for electrical and electronic products Guidelines for environmental testing simulating storage effects
- JB/T 50170-1999 Energy consumption classification of electric furnace for smelting white corundum
- HG 3624-1999 2,4-D technical
- GB/T 4227-1984 Stainless steel hot-rolled equal-leg angle steel
- GB/T 39461-2020 Data interface of the international logistics information system
- GB/T 39609-2020 Rules for geocode of address
- JB/T 8011.4-1999 Double-sided eccentric wheels for machine tool fixture parts and components
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：[email protected]