CB/T 3845-2000 Cross-shaped bollard for ships

CB/T 3845-2000 Marine Cross-type Bollard CB/T3845-2000 Standard download decompression password: www.bzxz.net

NCS 47.020.50
Series No.:7724—2000
Ship Industry Standard of the People's Republic of China
CB/T3845—2000
Replaces CB/T 3845—1999
Ship cross bollards
Ship cross btts.
Published on September 20, 2000
Commission of Science, Technology and Industry for National Defense
Implementation on January 1, 2001
CB/T3845--2000
This standard is the most suitable for CB/T 384-1999 frame clip chain. CB/T3845-1999 was directly adjusted from GB10106-88 in June 1999, according to the notice of the Standardization Department of the State Administration of Quality Supervision, Inspection and Quarantine on the abolition of professional standards and the national standards that should be converted after the cleanup and rectification, and the notice of the General Company of China on the transformation of relevant national standards for shipbuilding special standards into industry standards. This revision was compiled with reference to the structural types of Japanese JISF2804-19B2+ and British BSMA12 Part 2, and the column size was determined according to the specifications of the existing non-relay pipes in my country. According to the general situation and requirements of Chinese ships, this standard has been modified as follows: a) The base structure has been added; b) Type A and B in the original standard have been cancelled; and the diameter of the 6×30 cable has been deleted. This standard is made with reference to the requirements of GB/T554-1986 and GB/T558-1983. This standard replaces CB/T 3B45-1999 from the date of implementation. Appendix A of this standard is a reminder appendix. This standard was proposed by the National Technical Committee for Standardization of Super Ship Equipment and the implementation of this standard is under the jurisdiction of Jiangnan Shipyard (Group) Co., Ltd. The drafting unit of this standard: Dalian Ship Selection and Shipbuilding Corporation Comprehensive Technology and Economic Research Institute. The main drafters of this standard are Ye, Ziwu and Zhang Jisheng. This standard was first issued in December 1988. It was directly adjusted to an industry standard in June 1999. CB/T 3845--2000 This standard specifies the classification, requirements, test methods, inspection rules and markings of general cross-section piles (hereinafter referred to as cross-section piles). This standard applies to the design, manufacture and acceptance of cross-section piles for ship mooring and cargo pipe fixing. 2 Classification 2.1 Structural type and basic dimensions The structural type and basic dimensions of cross-section piles shall be in accordance with the following standards: 1. K
Explanation 1. The contraction form and size of the cross-shaped combustion column. Nominal maximum breaking load kN
2.2 Climbing index
CB/T 3845--2000
Basic size of piles
Suitable for large diameter of cable fuel
250×250
300×800
380×380
480×480
550×550
Cross-shaped pile with nominal true diameter of 150mm.
Ten-dimensional pile 150 CB/T3845-2000
3 Requirements
3.1 The materials for pile components are shown in Table 2.
Fiber sintering
Capsule 2 The main components of piles
Hand-made installation boundary
Vertical pile and horizontal pile
Lining, support plate, bottom plate
Seamless solution
Periodic structural period
Periodic structural period
3.2 Pile piles can be made directly from keyless steel pipes or steel plates. Material
Increase production height
A level
A delay
Standard number
GB/T 8162~1999
GB712-2000
GB 712-2000
3.3 When the pile is welded with steel plates, there shall be no more than two butt welds for each diameter of the pile. After welding, the weld shall be leveled. 3.4 The chain of the pile shall not have diffuse explosion, insufficient throat thickness and double thickness. 3.5 The bottom of the pile after shear welding shall have two degrees of climbing
3.6 The manufacturing size deviation of the cable pile is:
a) The outer diameter of the pile shall be less than +1%D (D is the diameter of the chain column); b) The roundness is less than 2mm1
C) The verticality of the cable pile is 3H/1000 (H is the height of the pile). 3.7 The surface of the pile should be smooth, the edges should be smooth, and the welds should be smooth. 2
CB/T 3845-2000
The strength test of the pile diameter can be carried out according to Appendix A (Appendix for reference). 3.8
4 Test method
4.1 Use measuring tools to check the appearance and measure the height and diameter of the pile. 4.2 Use caliper to check the surface quality and welding of the pile. Cracks, bends, molten metal and defects that hinder use are not allowed.
5 Inspection rules
5.1 After the pile is made, it shall be inspected by the technical inspection department of the manufacturer and a certificate of conformity shall be issued. 5.2 Inspection items
5.2.1 Carry out the inspection and measurement of the appearance and dimensions. The inspection shall meet the requirements of 1 and 3.6. 5.2.2 Appearance and welding quality control shall meet the requirements of 3.3 and 3.4. 5.2.3 After acceptance, the outer surface of the pile shall be smooth and uniform. 6. The pile shall be marked with the following: a) manufacturer name or mark b) model and standard number c) inspection seal d) date of manufacture or batch number.
CB/T 3845--2000
(Appendix of the attached document)
Strength connection of the world
A1 The strength calculation of pile column is shown in formulas (A1), (A2), (A3), (A4), (A5), (A6), where the bending strength calculation is shown in Figure A1, MaP-h.:
h-h+ D,/2 +d/2
T- P/Abzxz.net
+= 1/20 + 1/2Va,* + 42
S, /a21
M-bending moment, kN·cmt
-breaking load of the element, kN;
bending moment, see formula (A2) and Figure Al, cm, er bending stress, kN/cm;
Wwound modulus of pile, ctn\.
-shear force, kN/cn*,
pile shear volume, cm,
component force, EN/cm
cs material strength, kN/em
tight diameter station
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.