QB/T 2707-2005 Preparation and conditioning of leather physical and mechanical test specimens

This standard specifies the preparation of leather specimens for physical and mechanical tests and the methods of conditioning and testing in two standard atmospheres. This standard applies to all types of leather. QB/T 2707-2005 Preparation and conditioning of leather specimens for physical and mechanical tests QB/T2707-2005 Standard download decompression password: www.bzxz.net

ICS 69.140
Classification number: Y45
Registration number: 157592005
Light Industry Standard of the People's Republic of China
QR/T2707—2005
Replaces QE/T3812.2—1999
Leather
Physical and mechanical tests
Sample preparation and conditioning
Leather--.-Phsical and mechanical tcsts-Sampleprcparation andconditioning(1S0 2419:2002, Leather—Physical and mechanical icsts-Sampl:prcpatalion and 2005-03-19 issued
National Development and Reform Commission of the People's Republic of China2005-09-01 implemented
QH/T2707-2905
This standard is a revision of QR 3812.21990 for the measurement of physical properties of pressure test pieces for gas conditioning. This standard amends and adopts S0241y:2002 for the measurement of physical properties of pressure test pieces for gas conditioning (Lrhcr-Physicaandmcchaniua[lessSampleparationandconditioning]), and is the standard of the International Federation of Automotive Engineers and Chemists TTCS PP.
QB/T3812.2—1999 and other standards adopted 152419:J972: [S02419 has been revised, and IS02419:2002 has replaced 502419:1972.
This standard is based on TS02419:2002 and was re-written. This standard was based on the actual situation in my country. When adopting 1S258:2002, it was revised with a technical policy. The original standard did not have a "normative text" and stipulated in Article 5 that "sampling should be carried out according to TS0241R". The small standard has a "standard steam guide piece support chapter". Its number and order are in accordance with the Chinese legal readability, and the "technical and In the "Definition", 1 "am1opheT", the relevant content is merged with 2.2, without affecting the use of terms and definitions, and is consistent with the international terminology standards; in order to facilitate the general use of the attached "Notes", this standard also makes the following editorial modifications: except for the following ISO standard prefix:
The "International Standard" is changed to "This Standard" in the standard. Compared with Q/3512.21099, the following changes are added: 2 "Normative references", 3 "Terms and definitions", 4 "Standard air", 5 "Model", 6 "Selection and preparation of samples", 8 "Test", 9 "Test report" content; the "word section" is deleted.
In the standard issued by: China Light Industry Federation, this standard is the Chinese leather industry standard reform technical difference committee (5AC/:252:1, this standard should be the unit: China Development and Reform Commission, this standard is the drafter: China
This standard was first issued in October 1944 as the original national standard GB4689.21584:109 April 2009 converted into light industry standard BT3812.2-1999, this standard is the second time you change this standard, the original national light industry standard (B/3H12.2-1999) issued by the light industry level is the standard for the test of the performance of the light industry.
Leather physical and mechanical testing: sample preparation and conditioning QH/T2707-2005
This standard specifies the preparation for the quick inspection and testing of the machine and the method of conducting the test in the commercial atmosphere. This standard is a kind of "forget
2 normative pressure-inducing documentWww.bzxZ.net
10 to the safety three practical clauses. This standard flashes and becomes the market clause. The available documents can be used as a reference. Some changes (no error) are not applicable to the same version as the standard. However, the new version of this standard can be achieved by the code of this document. All references to the document without H are only applicable to this document. QB/T270-2005 chemical, mechanical and color test single parts (50241:2002, M0 D) 3 Terms and Definitions
The following terms and definitions apply to this document: 3.1
Standard air
The air is determined by the specified temperature and humidity. It is stored in the specified environment within the specified range. The air quality is guaranteed. 3.2
The sample is placed in a slow-flow pool at the specified temperature and humidity. The sample can be brought to the specified temperature by the slow-flow pool. This can be done by the specified temperature.
4 Standard air
Standard air and allowable deviations are shown in Table 1. Standard air and allowable deviations
Cloud shadow added
Five degrees/T.
J ±2
The following environment design can be used for air..., but the individual standards are not equivalent to 23/53
Publication/Exercise
: Only the health conditions of the M are reported separately, generally speaking, the air temperature is 2D), the standard air temperature is 2D), the standard air temperature is 2D), the standard air temperature is 2D), the standard air temperature is 2D), the standard air temperature is 2D), the standard air temperature is 2D), the standard air temperature is 2D, ... 2 Preparation of the sample: Use a knife to cut the sample from the hot surface (or the estimated surface). If there is no grain surface (grain mountain), cut the sample from the use. If the sample is selected, it should be conditioned before the initial use. 7 General table: Put the sample into the standard air, and the surface should be slightly touched by the stagnant air. The 48h conditioning should be carried out before the test.
8 Test
The test should be carried out in the standard air selected by the test manufacturer, and there will be other provisions in the test method. 9 Test report
The test report shall include the following contents:
Specimen name, serial number, type;
Detailed information on the selected product culture, sampling and Q/T2706-2005 or one or more standard gases (such as 2065% or 2350%)
Abnormal conditions in the test
Differences between actual work and this report:
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.