QB/T 2210-1996 Hand Drill

This standard specifies the product classification, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of hand drills. This standard applies to hand drills for manual drilling. QB/T 2210-1996 Hand Drill QB/T2210-1996 Standard download decompression password: www.bzxz.net

QB/T2210-1996
This standard is formulated on the basis of the former Light Industry Ministry Standard SG226-1981 "Hand-made Drill". This standard supplements the product type and makes corresponding adjustments to its basic dimensions. The inspection rules of the product adopt the sampling method specified in GB/T2828-1987 "Batch Inspection Count Sampling Procedure and Sampling Table (Applicable to Continuous Batch Inspection)", and further improve the product packaging, marking, transportation and storage requirements in accordance with the provisions of GB/T5305-1985 "Packaging, Marking, Transportation and Storage of Hand Tools".
This standard will replace SG226-1981 from the date of implementation. This standard is proposed by the Quality Standards Department of the China Light Industry Federation. This standard is under the jurisdiction of the National Tool Hardware Standardization Center. The responsible drafting unit of this standard: Shanghai Tool Industry Research Institute; participating drafting unit: Shanghai Automobile Tool Factory. The main drafters of this standard: Lin Meide and Wang Wei. 580
1 Scope
Light Industry Standard of the People's Republic of China
Hand Drill
QB/T2210--1996
This standard specifies the product classification, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of hand drills. This standard applies to hand drills for manual drilling. 2 Referenced Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard was published, the versions shown were all valid. All standards will be revised. Parties using this standard should explore the possibility of using the latest versions of the following standards GB/T230--1991 Rockwell hardness test method GB/T2828---1987 Batch inspection counting sampling procedures and sampling tables (applicable to continuous batch inspection) GB/T5305-1985 Hand tool packaging, marking, transportation and storage 3 Product classification
3.1 Type
Hand-held drills are divided into two types according to their use methods (indicated by S) and chest pressure type (indicated by X), and are divided into type A and type B according to their structure, as shown in Figures 1 to 4.
3.2 Basic dimensions
The basic dimensions of hand-operated drills are specified in Table 1.
Hand-held
Chest pressure type
3.3 Marking example
The marking of hand-operated drills consists of product name, type code, specification and standard number. Example: 6mm handheld A-type hand drill is marked as: Approved by China Light Industry Association on 1996-03-22
Clamping diameter
Implemented on 1996-12-01
Hand drill SA6QB/T2210
QB/T2210-.1996
9mm chest pressure B-type hand drill is marked as
Hand drill XB9QB/T2210
Figure 1 Handheld A-type hand drill
Figure 3 Chest pressure A-type hand drill
Handheld B-type hand drill
Figure 4 Chest pressure B-type hand drill
4 Technical requirements
4.1 Surface quality
QB/T 2210--- 1996
4.1.1 The surface of the hand drill should not have cracks, scars, burrs, rust spots and other defects that affect its use. 4.1.2 The paint of the hand drill should be of uniform color, without paint stagnation or paint peeling. 4.1.3 The electroplated parts of the hand drill should have a uniform coating color and should not have defects such as missing plating, burning, bubbles, and delamination. 4.1.4 The surface of the parts treated with blackening should have a uniform black oxide layer and should not have red, yellow, green spots or exposed bottom. 4.2 Performance
4.2.1 The parts of the hand drill should be able to be assembled and disassembled flexibly and reliably. 4.2.2 The hand drill should rotate flexibly without jamming. 4.2.3 The jaws of the hand drill chuck should be flexible to extend and retract, and there should be no obvious gap between the jaws when tightening. 4.3 Hardness
The heat treatment hardness of the jaws of the hand drill chuck should not be less than 44HRC. 4.4 Moisture content of wooden handle
The moisture content of wooden handle of hand drill shall not exceed 16%. 5 Test method
5.1 Dimension inspection
The dimensions of hand drill shall be inspected by universal measuring tools. 5.2 Surface quality inspection
The surface quality of hand drill shall be inspected by visual inspection. 5.3 Performance test
5.3.1 Test the rotation flexibility of hand drill by hand feel. 5.3.2 Visually inspect the gap between the jaws. 5.4 Hardness test
The hardness of the jaws of hand drill chuck shall be tested in accordance with the provisions of GB/T230. 5.5 Moisture content test of wooden handle
The moisture content of wooden handle of hand drill shall be determined by wood moisture tester. 6 Inspection rules
6.1 Products shall be inspected by the inspection department before leaving the factory, and shall be accompanied by a product certificate. 6.2 The acceptance inspection of products shall be carried out in accordance with the secondary sampling plan specified in GB/T2828. 6.3 The classification and grouping of unqualified products, inspection items, acceptable quality level (AQL) (number of unqualified products per 100 units of products) and inspection level (.) shall be in accordance with Table 2.
Classification and grouping of unqualified products
Inspection items
Hardness of clamp
Gland between jaws
Flexibility of rotation
Surface quality
Moisture content of wooden handlebZxz.net
Acceptable quality level (AQL)
Inspection level (iL.)
QB/T 2210-1996
Products rejected after inspection may be resubmitted for acceptance after classification or refurbishment by the manufacturer. 6.4
Marking, packaging, transportation, storage
The packaging, marking, transportation and storage of products shall comply with the provisions of GB/T5305.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.