HG/T 2254-1991 Photographic Chemicals Coupler COM-1

HG/T 2254-1991 Photographic Chemicals Coupler COM-1 HG/T2254-1991 Standard Download Decompression Password: www.bzxz.net

Chemical Industry Standard of the People's Republic of China
Photographic Chemical Coupler COM-1
HG2254-91
This product is white or slightly yellow powder. It is soluble in acetone, ethyl acetate, alcohol, benzene, hot acetonitrile and petroleum aldehyde ether, with a melting point of 95~98.
Molecular formula: CHs2CIN,O3
Relative molecular mass: 609.91 (according to the international relative atomic mass in 1987) Subject content and scope of application
This standard specifies the technical requirements, test methods, inspection rules, packaging, marking, transportation and storage of photographic chemical coupler COM-1.
This standard applies to coupler COM-1 for color film.2 Reference standard
Preparation of standard solution for impurity determination
Chemical reagents
Chemical reagents
Preparation of preparations and products used in test methods Sampling and acceptance rules for chemical reagents
GB6682 Specification for laboratory water
HG/T2414 Determination of colorant content of photographic chemicals Reversed-phase high performance liquid chromatographywww.bzxz.net
HG2256
Determination of ash content of colorants in photographic chemicals
HG2257
HG2258
3 Technical requirements
Determination of volatile matter of colorants in photographic chemicals Photographic chemicals! Determination of coupler solubility Coupler COM-1 should meet the requirements of the following table:
COM-1(CHCIN,O),%
Solubility
Volatile matter, %
Ash, %
Iron (Fe), %
Photographic properties
Infrared harmonic
Approved by the Ministry of Chemical Industry of the People's Republic of China on December 28, 1991. Press am, bzeono.ieom Customer standard Industry information free download Teaching guide
Implementation on July 1, 1992
4 Test method
HG2254—91
The standard solutions, preparations and products used in the impurity determination in this test method shall be prepared according to the provisions of GB602 and GB603 unless otherwise specified. The water used in the laboratory shall meet the third-grade water specifications in GB6682. 4.1 The determination of the content of the color former COM-1 (CgHszCN,O) shall be determined according to the provisions of HG/T2414, in which the main content of the standard sample shall not be less than 98%, and the control sample shall consist of the known impurities retained by the color former COM-1 and the adjacent chromatogram. 4.2 Solubility test
Determine according to the provisions of HG2258. The test solution shall be transparent, and trace insoluble matter is allowed. 4.3 Determination of volatile matter
Determine according to the provisions of HG2257. The drying temperature is 70-75°C, and the volatile content should be less than 10 mg: 4.4 Determination of ash
Determine according to the provisions of HG2256. The ash content should be less than 3 mg (keep the ash residue for iron determination). 4.5 Determination of iron impurities
Add 1 mL of hydrochloric acid to the ash residue in 4.4, dissolve it in warm water, add 10 mL of water and transfer it to a 25 mL volumetric flask, dilute it with water to the scale, and shake it well. Take 5 mL of the above sample solution, place it in a 50 mL colorimetric tube, add about 30 mg of ammonium persulfate and 5 mL of ammonium thiocyanate solution (100 g/L), dilute it with water to the scale, and shake it well. The color of the sample solution shall not be darker than the standard. The standard is to take 0.01 mg of iron (Fe) impurity standard solution and treat it in the same way as the sample. 4.6 Photographic performance test
Test according to the method agreed by the supply and demand parties. 4.7 Infrared spectrum identification
Put about 1.5 mg of sample in an agate mortar and grind it into 2um powder, add about 100 mg of dried spectrally pure potassium bromide fine powder, grind it thoroughly with an agate mortar, mix it and dry it. Press it into transparent thin slices on a tablet press, measure it on an infrared spectrophotometer in the range of 4000-400cm-1 wavenumber, and the infrared spectrum obtained should be consistent with the infrared spectrum of the standard sample. 5 Inspection rules
Sampling and acceptance shall be carried out in accordance with the provisions of GB619. 6 Packaging, marking, transportation and storage
6.1 Packaging
Packing unit 20kg. The inner packaging should be a double-layer plastic bag, and the plastic bag should be tied. The outer packaging is a fiberboard barrel. If special packaging is required, it shall be decided by negotiation between the supply and demand parties.
6.2 Marking
The outer packaging container shall be firmly marked with product name, standard number, registered trademark, net weight, gross weight, production batch number, photographic chemicals and date of manufacture, manufacturer name and address, and moisture-proof mark. The packaging container shall be accompanied by a quality inspection certificate.6.3 Transportation
Be careful during transportation, prevent moisture and heat, and do not damage the packaging. 6.4 Storage
The product shall be stored in a cool, dry and ventilated warehouse, and the storage period is 1 year. After the expiration of the period, it shall be inspected according to the provisions of this standard. If it meets the requirements of this standard, it can continue to be used. Standard Exchange Network.b2oo.cm Various standards industry resources free download Additional notes:
HG225491
This standard is proposed by the Science and Technology Department of the Ministry of Chemical Industry of the People's Republic of China. This standard is under the jurisdiction of the Photosensitive Material Technology Development Center of the Ministry of Chemical Industry. This standard was drafted by Qingdao Dyestuff Factory, with participation from the Photosensitive Material Technology Development Center of the Ministry of Chemical Industry and Beijing Chemical Factory. The main drafters of this standard are Hu Jialin, Zhuang Youqin, Wen Huiqiong, Cai Ting, and Guan Ruibao.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.