JB/T 8482-1996 Technical requirements for screw lathes

This standard specifies and supplements the general technical standards of machine tools such as GB 9061-88 "General Technical Conditions for Metal Cutting Machine Tools", ZBn J50 008.1-88 "General Technical Conditions for Machining Parts of Metal Cutting Machine Tools" and ZBn J50 008.3-88 "General Technical Conditions for Assembly of Metal Cutting Machine Tools" according to the structural characteristics and use requirements of screw lathes. This standard specifies the requirements for the manufacture and acceptance of screw lathes. This standard is applicable to screw lathes with a maximum workpiece length of 8000mm and a maximum workpiece diameter of 100mm. JB/T 8482-1996 Technical Conditions for Screw Lathes JB/T8482-1996 Standard download decompression password: www.bzxz.net

Machinery Industry Standard of the People's Republic of ChinaWww.bzxZ.net
JB/T 8482-96
Screw Lathe
1996-11-07 Release
Technical Conditions
1997-1-01 Implementation
Ministry of Machinery Industry of the People's Republic of China
JB/T482-96
This standard specifies the structural points and application requirements of machine tools, and generalizes and supplements the technical standards of B9061 Metal Cutting Machine Tool Table 2EnJ0CCH.1-General Technical Conditions for Mechanical Parts of Fully Cutting Machine Tools MnI500C8.3B Metal Pressing and Assembly Technology Machine Case 3. This standard is from the paragraph, 215300567 state locomotive lathe manufacturing and acceptance technology, this standard is the national metal fast cutting sinker standardization technical committee public funds: international release lathe research institute!
six standard starting rate unit, on the year of this list research quantity 1 total range
people's republic of china machine operation industry standard
screw lathe
technical parts
wood standard specification is the final lathe manufacturing and acceptance requirements. JBT 84HZ96
this operation uses the following large T piece length 2m. The design of the large workpiece diameter is more than 1m seedling wire social lathe 1 reference standard
one gram standard piece gas content preparation text, the design of this standard is used as the total text of this standard, this standard is issued or the version is valid, the standard is carefully revised, the use of technical standards winter proposal discussion to make sure the latest acceptance card. t:[35226. 1 …-35.1. k period electric point, equipment part I: certification H support technical provisions -
13 :139-88
Z 150 55388
ZB J5:1 0:S8
ZTn J8G 303. E-x8
Zhm 150 308. ::
2 135 01665
Z J53 4
General requirements
Enterprise body cutting machine tool technology
Metal cutting machine tool accessories installation quality requirements system metal cutting machine description determination
Standard cutting machine page
Metal actual method
Concept quality cutting machine
Full case original machine
Limited noise level determination
Machine workpiece pressure technical parts
Oil matching technical parts
Liquid system application technical conditions
Experimental lathe accuracy
Metal cutting machine tool analysis classification
According to 4 standards, when collecting the machine, it is necessary to check B, JU8.1ZJSC.3 and other international standards at the same time! 4. The items listed in Table 1 are approved by the Ministry of Industry in 199610 and are implemented in 19970. 4.2 Special accessories that can be used to expand the performance of the machine are supplied according to the requirements of the user. 5. Safety and Health 5.1 When the machine tool is in operation, the parts that have been cut and cooled should be equipped with protective devices. 5.2 The parts of the machine tool rail and the main screw that are easily worn by dust and chips should be equipped with protective devices, and the replacement gears and pulleys must be equipped with protective devices.
S.3 There should be no abnormal load noise or impact during the aircraft transfer. The boarding noise sound pressure level should not exceed 75dB when the noise level is measured under the various suction systems of the above parts.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.