INdex
GB standard
Standard category
Machinery Industry
It standard
Industry Standard
Chemical Industry It standard Petrochemical ZB Industry Light industry Railway industry Shipping industry Measurement standards

GB/T 2861.3-1990 C-type guide pins for die guides

time: 2024-08-11 13:48:06
  • GB/T 2861.3-1990
  • Abolished

Basic Information

  • Standard ID:

    GB/T 2861.3-1990

  • Standard Name:

    C-type guide pins for die guides

  • Chinese Name:

    冲模导向装置 C型导柱

  • Standard category:

    National Standard (GB)

  • Date of Release:

    1990-07-23

  • Date of Implementation:

    1991-05-01

  • Date of Expiration:

    2008-10-01

standard classification number

  • Standard ICS number:

    Mechanical Manufacturing>>Chipless Processing Equipment>>25.120.30 Molding Equipment and Casting Equipment

  • China Standard Classification Number:

    Machinery>>Process Equipment>>J46 Mold

associated standards

Publication information

  • publishing house:

    China Standards Press

Other Information

  • Release date:

    1981-12-29

  • Review date:

    2004-10-14

  • Drafting Organization:

    Guilin Electrical Appliance Research Institute

  • Focal point Organization:

    National Technical Committee for Mould Standardization

  • Publishing Department:

    National Standardization Administration

  • Competent Authority:

    National Standardization Administration
Introduction to standardsDescription (Translated English) / download

Skip to download

Summary:

GB/T 2861.3-1990 C-type guide pin for die guide device GB/T2861.3-1990 Standard download decompression password: www.bzxz.net
Standard contentStandard content

Some standard content:

National Standard of the People's Republic of China
Guide unit for press tools
Guide plllars, type C
Subject content and scope of application
GB/T 2861,3-90
Replaces GB 2861.3-81
This standard specifies the materials, heat treatment, technical conditions, structural types and specifications of C-type guide pillars for press guide units. This standard applies to rolling guide die sets for press dies. Referenced standards
Technical conditions for die set parts
GB/T 12446
Technical conditions for YB9 chromium bearing steelWww.bzxZ.net
3 Materials, heat treatment, technical conditions, structural types and specifications for guide pillars 3.1 Material: GCr 15 YB 9.
3.2 Heat treatment: Hardness HRC 62~66.
3.3 Technical conditions shall be in accordance with the provisions of GB/T12446. 3.4 Structural types and specifications are shown in the figure and table.
Approved by the State Administration of Technical Supervision on July 23, 1990 and implemented on May 1, 1991
3.5 Marking example:
GB/T 2861.3-—90
GB 145- 85
R* is determined by the manufacturer.
C-type guide column with diameter d=25mm and length L=160mm: Guide column C25×160 GB/T 2861.3
Additional instructions:
GB/T2861.3—90
This standard is proposed by the Ministry of Machinery and Electronics Industry of the People's Republic of China. This standard is under the jurisdiction of the National Technical Committee on Mold Standardization. This standard was drafted by the Mold Branch of Guilin Electric Science Research Institute of the Ministry of Machinery and Electronics Industry. The main drafters of this standard are Wang Huachang and Qin Guangwei. This standard is entrusted to the Mold Branch of Guilin Electric Science Research Institute of the Ministry of Machinery and Electronics Industry for interpretation.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
  • Recommended standards
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：wymp4wang@gmail.com