QB/T 1622.10-1992 Stainless steel utensil basin

This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage requirements of stainless steel basins. This standard applies to basins formed by stamping of stainless steel plates. QB/T 1622.10-1992 Stainless Steel Utensil Basin QB/T1622.10-1992 Standard download decompression password: www.bzxz.net

Light Industry Standard of the People's Republic of China
Stainless Steel Utensilsbzxz.net
Subject Content and Scope of Application
QB/T 1622.10—1992
This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage requirements for stainless steel basins. This standard applies to basins formed by stamping of stainless steel plates. 2 Reference standards
GB/T3280 Stainless steel cold-rolled steel plate
GB/T6060.4 Surface roughness comparison sample Polished surface GB/T6062 Profile method Stylus surface roughness ovality measuring instrument Profile recorder and center line profile method GB9684 Sanitary standards for stainless steel tableware containers QB/T1622.1 Stainless steel utensil terminology
QB/T1622.2 Stainless steel utensil
: Product classification
QB/T1622.3 Stainless steel utensil
Inspection rules
QB/T 1622.4 Stainless steel utensil
3 Terms, symbols, codes
Marking, packaging, transportation, storage
3.1 The terms should comply with the provisions of QB/T1622.1. 3.2 Symbols and codes shall comply with the provisions of Article 4.3 of QB/T1622.2. 4 Product classification
4.1 Product varieties and types shall comply with the provisions of Articles 4.3.2.1 to 4.3.2.3 of QB/T1622.2. 4.2 Specification division
a. It shall comply with the provisions of Article 4.3.2.5 of QB/T1622.2; b. It shall be expressed by the diameter of the basin, starting from 14cm, with a step difference of 2cm. 4.3 Product marking
4.3.1 Product marking shall comply with the provisions of Article 4.3 of QB/T1622.2. 4.3.2 Marking example
The diameter is 26cm, the factory design serial number is 1, and it is a polished ordinary spherical basin. Basin Q1-26QB/T 1622.10
5 Technical requirements
5.1 Hygiene requirements shall comply with the provisions of GB9684. 5.2 Material requirements
Stainless steel plates shall comply with the provisions of 1Cr18Ni9 or 0Cr19Ni9 in GB/T3280, or other grades with performance not lower than the above provisions.
Approved by the Ministry of Light Industry of the People's Republic of China on November 10, 1992 and implemented on July 1, 1993
5.3 Product quality requirements
QB/T 1622.10-1992
5.3.1 Inspection items, grades and quality requirements shall comply with the provisions of the following table. No.
Inspection Item
Polished Surface Roughness
Sanding Surface Roughness
Cutting and Pressing Edge
Identification Mark
Grade Judgment
Unqualified
Superior Product
Not More Than 1% of the Diameter
Cumulative Length at the Edge Not More Than
Not Allowed
Not Allowed
Not Allowed
2% of the Diameter, Other Other parts are not qualified. The decoration is not more than 1.5% of the diameter. The cumulative length of the edge is not more than 4% of the diameter. Other parts are not qualified. The inner wall is not more than half of the height and the width is 0.05~~0.20 per 600 circumference. Other parts are not allowed to be 1~5, one place is not more than 8, one place is not more than 4, one place is not allowed to be more than 4, and the tip is not allowed to be R. The maximum allowable value is 0.20, uniform, neat, and scratch-free R. The maximum allowable value is 1.60, uniform, neat, continuous, tight, smooth, with a gap of no more than 0.20 with the wall. Correct, leak-free, properly positioned, clear writing, no visible text on the reverse side. Excellent products: no more than one C-class unqualified; Standard products: no more than two C-class unqualified;
Qualified products: no more than one B-class and one C-class unqualified or three C-class unqualified. 6 Test method
6.1 Specifications
6.1.1 The capacity is measured with a measuring cup or measuring stick, and its value shall comply with the provisions of Article 4.2. 6.1.2 The diameter is measured with a steel ruler or vernier caliper, and its value shall comply with the provisions of Article 4.2. R. The maximum allowable value is 0.20
R. The maximum allowable value is 1.60
Continuously roll tight, with little gap between the wall
Correct, leak-free, legible writing
6.2 Product quality requirements
6.2.1 The roundness is measured with a vernier caliper or steel tape measure. The maximum and minimum values ​​of the diameter shall meet the requirements of Article 5.3.1. 6.2.2 The values ​​of wrinkles and pits are measured with a steel tape measure or vernier caliper. The values ​​shall meet the requirements of Article 5.3.1. 6.2.3 The scratches are measured with a steel tape measure and a feeler gauge. The values ​​shall meet the requirements of Article 5.3.1. 6.2.4 The roughness of the polished and sanded surface shall be checked according to GB/T6062 or GB/T6060.4. The results shall meet the requirements of Article 5.3.1. 6.2.5 The edges are measured by visual method, hand touch method and feeler gauge. The results shall meet the requirements of Article 5.3.1. 6.2.6 Visual inspection and hand touch shall be used for identification marks, and the results shall comply with the provisions of Article 5.3.1. Inspection rules
Should comply with the provisions of QB/T1622.3.
8 Marking, packaging, transportation, storage
Should comply with the provisions of QB/T1622.4.
Additional instructions:
QB/T1622.10—1992
This standard was proposed by the Quality Standards Department of the Ministry of Light Industry. This standard is under the jurisdiction of the National Daily Hardware Standardization Center. This standard was drafted by Tianjin Stainless Steel Ware Factory, Shanghai Stainless Steel Ware Factory III, Guangdong Yangjiang Stainless Steel Ware General Factory, and Liaoning Fushun Stainless Steel Products Industrial Company.
The main drafter of this standard is Wang Shulin.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.