HG/T 2058.2-1991 Glass-lined finned thermometer sleeve

HG/T 2058.2-1991 Glass-lined finned thermometer sleeve HG/T2058.2-1991 Standard download decompression password: www.bzxz.net

Chemical Industry Standard of the People's Republic of China
Glass Finned Thermometer Cover
Subject Content and Scope of Application
HG/T2058.2-91
This standard specifies the structure and assembly type, parameters, main dimensions and technical requirements of pond glass finned thermometer covers. This standard is applicable to finned thermometer covers for pond glass stirring vessels with nominal pressure less than or equal to 1.0MPa, medium temperature higher than -20C and lower than or equal to 200C, and equipped with paddle or impeller agitators. 2 Reference Standards
GB700 Carbon Structural Steel
GB5679
Mallet Cast Iron
Hydraulic Pressure Test of Pond Glass Equipment Method
GB7994
GB7996 Nominal volume and nominal diameter of glass containers GB8163 Seamless steel pipe for conveying fluids
ZBG94004 Technical conditions for glass equipment
HG2-538 Polytetrafluoroethylene plates, rods, fillers, drawing specifications and uses HG/T2050 Gaskets for glass equipment
HG/T2105 Slip-on flanges for glass equipment
3 Types, basic parameters and main dimensions
3.1 The finned thermometer sleeve structure is divided into two types, Type A and Type B. Type A is a finned thermometer sleeve without an overflow measuring head device. Its basic parameters and dimensions are shown in Figure 1, Table 1, Table 2 and Table 4. Type B is a thermometer sleeve with a temperature measuring head device. Its basic parameters and dimensions are shown in Figure 2, Table 2, Table 3, and Table 4.
3.2 Marking:
Standard number
Thermometer sleeve length L
Nominal diameter of the thermometer sleeve dN
Nominal pressure of the container PN
Type of the thermometer sleeve
Name: Thermometer sleeve
Example:
Fin without temperature measuring head device Type thermometer sleeve, the nominal pressure PN of the container is 0.6MPa, the nominal diameter dN of the thermometer sleeve is 65mm, and the height H is 1350mm.
Thermometer sleeve A0.6×65-1350HG/T2058.2--91. Approved by the Ministry of Chemical Industry of the People's Republic of China on July 6, 1991, and implemented on January 1, 1992
Surface sugar glass
HG/T 2058.291
M27×2
HG/T2058.2-91
Surface treatment glass
HG/T2050-91
HG/T2105--91
GB5782—86
GB617086
GB 97.1—85
Nominal diameter of thermometer sleeve
Matched pipe port
Nominal diameter
HG/T2058.2—91
Loop flange
Details
Table 2 Size table
KTH350 or Q235-A
Assembly
Q235-A
Sugar glass
See Table 2
①A-type finned overflow gauge sleeve dN32 specification. The end reducer @25×3.5 can be cancelled, and the inner @32×4 pipe is manufactured for direct sealing, but the height H is not noted:
③B-type finned thermometer sleeve has no dN32 specification. 128
HG/T205091Www.bzxZ.net
HG/T2105-91
GB5782-86
GB6170-86
GB 97.1—85
GB985.1-86
GB123576
WEPM-0.18||tt ||HG/T 2058.2-- 91
Details
Junction box
Loop flange
Wire retaining ring
O-ring 28×3.5
Thermometry head sleeve
Compression spring 0.8×8×30
Ceramic end face platinum resistor
Assembly
KTH350 or Q235-A
Assembly
Q235-A
Spectrum glass||tt| |Q235-A
Polytetrazolyl
Red paper cypress
Assembly
See Table 2
Nominal diameter
Mixed mixing vessel
Volume VN
Nominal diameter DN
L series
S series
HG/T2058.2-91
Table 4 Dimension table
Reference weight, kg
Nominal pressure, MPa
Equipped with paddle stirrer
Equipped with impeller stirrer
Nominal diameter
Equipped mixing container
Volume VN
4 Technical requirements
Nominal diameter DN
L series
S series
HG/T2058.291
Continued Table 4
4.1 The steel pipe material used for the glass casing is No. 10 steel, which is accepted according to the provisions of GB8163. 4.2 According to the technical conditions of the glass fin thermometer sleeve, the reference weight is kg
and the nominal pressure is MPa
. 4.3 After the B-type fin thermometer sleeve is assembled, the test pressure after the glass is weighed as specified in Table 1 of GB7994 standard is carried out together with the installed equipment for water pressure test. The test pressure is the nominal pressure of the installed container. The test result should be leak-free. The material of the temperature measuring head sleeve can be provided according to the needs of the user, but it must be resistant to corrosion by the working medium. 4.4
5 Packaging, transportation and storage
5.1 The sugar glass surface should be wrapped with soft objects and firmly fixed in a wooden box. 5.2 No collision is allowed during handling or transportation, and the packaging box shall not be inverted. 5.3 The product should be accompanied by a packing list, a certificate of conformity and an instruction manual. 5.4 The product should be stored indoors and shall not be stacked or inverted in the open air. 131
Additional Notes:
HG/T2058.2—91
This standard was proposed by China National Chemical Equipment Corporation. This standard is under the jurisdiction of the National Standardization Technical Committee for Glass Equipment. This standard was drafted by Shanghai Industrial Glass Porcelain Factory, and the Shanghai Pharmaceutical Design Institute of the State Drug Administration participated in the drafting. The main drafter of this standard was Gu Guoyang, and the participating drafters were Bao Aiyuan and Huang Yinhua.132
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.