HG/T 2255-1991 Photographic chemicals coupler COC-1

HG/T 2255-1991 Photographic Chemicals Coupler COC-1 HG/T2255-1991 Standard Download Decompression Password: www.bzxz.net

Chemical Industry Standard of the People's Republic of China
Photographic Chemicals
Color-Forming Agent COC-1
HG2255-91
This product is white or slightly pink powder, soluble in organic solvents such as chloroform, acetone, ethyl acetate and alcohol. Melting point is 135~142℃.
Molecular formula: CaHg, CI, NO3
Relative molecular mass: 494.5 (according to the 1987 international relative atomic mass) 1 Subject content and scope of application
This standard specifies the technical requirements, test methods, inspection rules, packaging, marking, transportation and storage of the color-forming agent COC-1 for photographic chemicals.
This standard applies to the color film color coupler COC-1.2 Reference standards
GB602 Chemical reagents
Chemical reagents
Preparation of standard solutions for impurity determination
Preparation of preparations and products used in test methodsGB619
Sampling and acceptance rules for chemical reagents
GB6682
Specifications for laboratory water
HG/T2414 Determination of color coupler content in photographic chemicals Reversed-phase high performance liquid chromatography HG2256 Determination of ash content in color couplers for photographic chemicals Determination of volatile matter in color couplers for photographic chemicals HG2257
HG2258
Determination of solubility of color couplers for photographic chemicals 3 Technical requirements
Color coupler COC-1 should meet the requirements of the following table:||tt ||COC-1(CmHCl,NO%
Solubility
Volatile matter, %
Ash, %
Iron (Fe), %
Photographic properties
Infrared spectrum
1991-12-28 approved by the Ministry of Chemical Industry of the People's Republic of China. Standard exchange network mm.basoea.cum. Customer standard industry data free download index
1992-07-01 implementation
4 Test method
HG2255-91
The standard solutions, preparations and products used in the impurity determination in this test method are prepared according to the provisions of GB602 and GB603 unless otherwise specified. The laboratory water should meet the third-grade water specifications in GB6682. 4.1 Color former COC-1 (CgCI, NO) content The determination of the amount shall be determined according to the provisions of HG/T2414, in which the main content of the standard sample shall not be less than 98%, and the control sample shall be composed of the color former COC-1 and its adjacent chromatographically retained known impurities. 4.2 Solubility testbzxZ.net
shall be determined according to the provisions of HG2258. The test solution should be transparent, and trace insoluble matter is allowed. 4.3 Determination of volatile matter
shall be determined according to the provisions of HG2257. Bake at a temperature of 100~105C, and the volatile content should be less than 10mg. 4.4 Determination of ash
shall be determined according to the provisions of HG2256. The ash content should be less than 3mg (the ash residue is retained for iron determination). 4.5 Determination of iron impurities
Add 1mL of hydrochloric acid to the ash residue in 4.4, dissolve it in warm water, add 10mL of water and transfer it to a 25mL volumetric flask, dilute it to the scale with water, and mix well. . Take 5mL of the above sample solution and place it in a 50mL colorimetric tube, add about 30mg of ammonium persulfate and 5mL of ammonium thiocyanate solution (100g/L), dilute with water to the scale, spread evenly, the color of the sample solution shall not be darker than the standard, the standard is to take 0.01mg of iron (Fe) impurity standard solution and treat it in the same way as the sample at the same time, 4.6 Photographic performance test
The test shall be carried out according to the method agreed by the supply and demand parties. 4.7 Infrared spectrum identification
Put about 1.5mg of the sample in an agate mortar and grind it into 2μm powder, add about 100mg of dried spectrally pure potassium bromide fine powder, grind it thoroughly with an agate mortar, mix it and bake it, press it into a transparent thin sheet on a tablet press, and measure it on an infrared spectrophotometer in the wave number range of 4000~400cm. The obtained infrared spectrum should be consistent with the infrared spectrum of the standard sample. 5 Inspection rules
Sampling and acceptance shall be carried out in accordance with the provisions of GB619. 6 Packaging, marking, transportation and purchase and storage
6.1 Packaging
Packing unit 20k: The inner packaging should be a double-layer plastic bag, and the plastic bag should be tied. The outer packaging should be a fiberboard barrel. If special packaging is required, it shall be decided by negotiation between the supply and demand parties.
6.2 Marking
The outer packaging container shall be firmly marked with the product name, standard number, registered trademark, net weight, gross weight, production batch number, photographic chemicals and factory date, manufacturer name and address, and moisture-proof mark. The packaging container shall be accompanied by a quality inspection certificate.6.3 Transportation
Handle with care during transportation, and avoid moisture and heat. Do not damage the packaging. 6.4 Storage
The product should be stored in a cool, dry and ventilated warehouse. The storage period is 1 year. After the expiration of the period, it shall be inspected according to the provisions of this standard. If it meets the requirements of this standard, it can continue to be used. 8
Standard obtained from mm.zc Various standards industry information can be downloaded for free. Additional notes:
HG2255
This standard was proposed by the Science and Technology Department of the Ministry of Chemical Industry of the People's Republic of China. This standard is under the jurisdiction of the Photosensitive Material Technology Development Center of the Ministry of Chemical Industry. 9
This standard was drafted by Beijing Chemical Plant, and the Photosensitive Material Technology Development Center of the Ministry of Chemical Industry and Qingdao Dye Factory participated in the drafting. The main drafters of this standard are Guan Ruibao, Liu Jicheng, Cai Ting, and Wen Huiqiong. Standard exchange network ww, bzsosD.con Various standards industry information can be downloaded for free.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.