JB/T 10231.12-2002 Tool product testing methods Part 12: Side and face milling cutters

This part specifies the inspection methods and inspection instruments used for the inspection of various three-sided and face milling finished products. This method is not the only one. This part is applicable to the inspection of three-sided and face milling cutters produced according to GB/T 6119 and three-sided and face milling cutters with inserts produced according to JB/T 7953. This part is applicable to the inspection of three-sided and face milling cutters produced according to GB/T 6119 and three-sided and face milling cutters with inserts produced according to JB/T 7953. JB/T 10231.12-2002 Tool product inspection methods Part 12: Three-sided and face milling cutters JB/T10231.12-2002 Standard download decompression password: www.bzxz.net

1C$25.*00.20
Mechanical Industry Standard of the People's Republic of China
JB/T10231.12—2002
Tool product testing methods
Part 12: Side and Face milling cutter
Toolinspaction methods
Pari 12: Side and Face milling cutters2002-07-16issued
2002-12-01implemented
Before issuance by the State Economic and Trade Commission of the People's Republic of China
2 Standardization document
3 Inspection basis
4 External die
5 Surface roughness
Circularity
Testing part
Testing method
Testing tools
General thickness and external diameter
Front angle, back angle,
Span test part
Testing method
Detector other
Standard state,
Standard surface engineerbzxz.net
JR/T10231.12-2002
Central certification is proposed by China Federation of Industry and Commerce. Foreword
Standard Technical Committee of Beijing Tool Factory This standard was drafted by Beijing Tool Factory. The drafter of this standard: Zhi Zhengwei,
JB/T10231.12—2002
1 Scope
Testing methods for tool products
Part 12: Three-face milling elements
JB/T 10291.122002
This standard specifies the testing methods for various three-face milling cutter products and the detectors used. This method is not applicable to the testing of three-face milling cutters produced according to GRT119 and double-face milling cutters produced according to B/T7953. 2 Normative references
The references in the above documents may be cited in this part of T10231 and thus become the references of this part. For dated references, their subsequent amendments (excluding amendments) or revisions are not applicable to this part. However, the latest versions of these documents may be used in accordance with the agreement reached between the parties. For undated references, the latest versions shall apply to this part.
GBT 6119.1—1993 [Standard Standard for Use of Standards (C5VIS 02587: 1972) GB611 9.21996 Three-light milling small parts H/T7953-1999 Mirror gear three-side edge milling force
B1031.12(01 Cutting tool product test method Part 1: General 3 Test basis
Related product standards and drawings,
4 Appearance
According to the regulations of Chapter 4 of JB/T10231.1-20K1. 5 Surface roughness
B door 102311·-2(01 Chapter 5. 6 Circular runout
6.1 Test part
Slight runout test part: Milling cutter blade: detection of end face runout: inspection method of milling end blade (see Figure 1)
6.2.1 The radial runout of the peripheral cutting edge to the inner hole axis is measured by the indicator. Read the difference between the maximum and minimum values ​​of the indicator pointer and the maximum positive value.
6.2.2 The end face runout indicator of the end cutting edge (side plane) to the inner hole axis is directly touched on the cutting edge near the outer diameter, rotate the core, and make the tool rotate one circle. Read the difference between the maximum and minimum values ​​of the indicator pointer and the maximum difference between the adjacent teeth on both ends of the cutting edge. The maximum circular runout value is the required value. -
.IB/T10231.12—2002
6.3 Testing equipment
a: Indicator with a required value of 0.01mm:
b Magnetic table stand:
, core module;
d) Runout inspection instrument
7 The thickness and outer diameter of the milling cutter shall be in accordance with the provisions of 10.2 in 8/110231.1—2
B The inner hole shall be determined in accordance with the provisions of JB/T10231.1—2001. 9 Rake angle, back angle, side clearance angle
9.1 Testing location
Rake angle, back angle see Figure 12, side clearance angle see Figure 3. 9.2 Testing method (see Figure 4)
9.2.1 Rake angle
IB/T10231.12—2002
See Figure 4. Make the working surface of the multi-blade angle gauge bear against the adjacent tooth of the tooth to be measured, adjust the tool to make the working surface of the rake angle ruler contact with the front cutting surface of the tooth to be measured, and make the working surface of the back angle ruler contact with the tooth to be measured, then the rake angle value can be read. 9.2.2 Back angle
See Figure 4. Make the working surface of the multi-blade angle gauge bear against the adjacent tooth to be measured, adjust the tool to make the working surface of the back angle ruler contact with the tooth to be measured, then the back angle value can be read. 9.2.3 Side follow angle
Make the working support of the multi-edge angle gauge rest on the side of the gear being measured, and adjust the tool so that the working surface of the back angle gauge is in contact with the side of the cutter tooth. The side follow angle value can be obtained as follows: 9.3 Testing equipment
Multi-edge angle gauge.
1℃ Hardness
Safety [023].]—21 Mongolia Chapter 11:
According to m0231.1—2(K) Chapter 13
12 Packaging
According to JD123!.1—20K0 Chapter 14
13 Surface treatment
According to T10231.1—2001 Chapter 15.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.