GB/T 14413-1993 Marine portholes

This standard specifies the classification, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of marine portholes. This standard applies to portholes installed on marine vessels and ships, and can also be used as a reference for portholes installed on inland vessels. GB/T 14413-1993 Marine Portholes GB/T14413-1993 Standard download decompression password: www.bzxz.net

UDC 629. 12. 011. 83
National Standard of the People's Republic of China
GB/T1441393
Sidescuttles for ships
Published on 1993-05-24
Implemented on 1994-01-01
Published by the State Administration of Technical Supervision
W. Main content and scope of application
Applicable standard
4 Production route classification-
5 Technical requirements
Test method
Burning test rules
8 Marking, packaging, transportation and storage
Maximum allowable strength of anti-recording windows (supplement) List
National Standard of the People's Republic of China
Sidescuttles for ships
This standard is equivalent to the international standard IS01751 "Building - Glare windows". 1 Subject content and scope of application
GB/T 14413:93
This standard specifies the classification, technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of ship's glare windows (hereinafter referred to as glare windows).
It is applicable to the glare windows installed on seagoing ships and warships, and can also be used as a reference for the glare windows installed on inland vessels. 2 Reference standards
(iB191 Packaging storage transparent pictorial mark
G3385 Ship's unshielded windows and rectangular windows toughened safety glass non-destructive strength test method GI6388: Transport packaging delivery and receipt marks
G3 8242-3 Ship equipment terminology Deck accessories GB11582 Amine commercial window tight gasket
GB119-16 Marine toughened safety glass
GB/11435 Jin Ship window positioning
CB/292 Aluminum alloy anodizing treatment
CB/7. 3413 Hot dip galvanizing general process
3 Terms
3.1 Ship curtain side scules
Comply with the 1971 International Convention for the Safety of Life at Sea and the shipbuilding standards, and are equipped with watertight circular chambers on the main panel, superstructure and deck enclosure. 3.2 MainIratne
Main frame connected to the installation part,
Frame for type window IIIπ and equipped with glass. 3.4 Fasteners [asters
General term for hinges and locking devices of round holes of plastic windows that ensure radiation strength and permanent requirements. Hinges with oblong hinge holes shall not be counted as fasteners
3.5 Other terms are in accordance with GB 8212.3 4 Product classification 4.1 Types and applicable scope of windows Approved by the State Bureau of Technical Supervision on May 24, 1993 and implemented on January 1, 1994 GB/T 14413.93 The types of windows and their applicable scope are specified according to their characteristics as shown in Table 1 Table 1 Types of windows Ring opening mode Idle mode Right opening and closing mode (R) (N)
Material combination code
Wind cover opening
Installation method Bolt
F installation
Screw removal installation
Welding installation
(LR)(N)
Avoidance method
Hanging style
Example of code to be collected
Chasing river solid
A2DC-1.1-1120-Y1
Sea ship energy magic middle plate or
A250-RW-212]-Y2, full load water A300-5W-223C Above the Y1 line, no general opening of A35U-NB3-112J-Y2 is allowed, and the space to be watertight and A-1G1-NW.212G-Y1 airtight
331t233
$200-R3-112G-Y1
The most or the most important passenger ship
B2501W-222J-Y2 can be selected above the deck or (Y"
11300-SW-922G-YThe end of the superstructure or
356-S3-112,I Y1
B3401-NW-233Gi-Y2
On the deck of non-passenger ship
One is the superstructure
B450-N13-3331Y1 and the end
The passenger seat middle plate or the trunk
The first phase
C200LRB-229-Y1
The above pipe layer superstructure training
jC250 1.RW-230.Y2
3r0-NB-1HY2
C350-NW-23J. Y1
surface and movable end
non-passenger ship lower middle plate condition
on the first joint exit way to build
on the wall measurement and rear end
method: break the installation position 1: the installation position of the GB/14356 provisions of A type window locking device called. There are two kinds of nuts: tightening and ring-shaped, according to the requirements of the installation part, the following instructions should be given when selecting.
4.2 Basic dimensions of general windows
4.2.1 Type A 1.B (RB) Bolt-mounted left (right) opening window according to Figure 1 and Table 2 W.D-300, 350, 40K
D=200, 25u
GB/T14413—93
1-1 Window flange; 2—Fan cover; 3—Air vent cover; 4—Second ring; 5—Pressure ring; 6—Sealing element; 7—Locking device; 8—Link pin Note: This is 1, R type is symmetrical.
Transparent size
Fixture number
Installation fan plate
Installation screws
W.GB/F14413--93
4.2.2A type S3 type-screw installation common sensitive inlaid window according to Figure 2 and Table 3. D300.35kt.40#
1 Main panel 2 Window; 3--Yan; 4-Glass: 5 Clamping ring; 6: Plastic: 7 Clamping mouse: 8 Chain Hallwww.bzxz.net
Number of fastening parts
Storm cover
Dry damp class
Installation screw gun
Circumferential opening
W.GB/T 1441393
4. 2. 3 A type NB type bolt installation surrounding fixed window according to Figure 3 And table 4,u,ko.d
-20,250
main window frame: 2 storm cover 13—tightening bad; 4 eardrum: 5 penetration trapped; lock system installation: 7 hinge pin: 8 countersunk burst table 4
number of complex hardware
wind cover
installation screw control
surrounding opening
W.GB/T14413—93
4.2.4 A type 1.W (RW) type-connection installation left (right) opening can be tightly pressed according to Figure 4 and table 5.D3kl, 3, 40
2 =200.250
1 main window hinge + 2 window sash mark: 3 storm benefit; 1 slope: 5—H system class: G—seal doctor? Locking device 8 hinge pin
method: This figure is Lw-RW and is symmetrical to this,
light transmission ruler
fastener number
W.GB/T 14413-93
4.2.5A type SW type welding installation hinged plastic window according to Figure 5 and Table 6, D-300.351,200
D=200,250
1-main frame; 2 window frame 3 energy; 4 glass 5 clamping ring: 6 sealing; 7 locking device; 8 chain pin
light ruler at
-15″
fastening cattle number base
wind cover
window sash frame
surrounding opening
W.GB/T14413--93
4.2. 6A type NW type welding installation fixed type aviation tightness according to Figure 6 and Table 7. D-300,350,400
1-main balance;2 storm blue;3-hill tightening ring;4 dare to screw; seal lock release section: 7--hinge pin;8 countersunk screw table 7
Suiguang ruler blade
Fastener number
Wind cover window sash
W.GB/T 14413-93
4. 2.7B type LIB (R) type-screw installation left (right) open or window according to Figure 7 and Table 8. -340.35n.400.450
(2·2uu.25h)
1-soil with mark; 2-frame; wind cover; 4-glass. Tightening ring: 3-sealing net; 7-locking case, 3-hinge pin Note: This figure is 1, R type, R1B type is the opposite ring. Transparent size
Number of fasteners
Windshield
Window panel
Installation butterfly bolt
W.GB/T14413-93
4. 2. 8 Type SR or - bolt installation hinge type and tightness according to Figure 8 and Table 9. 1J-300.351-400,150
20),25
Card cabinet: 2-window sash drag + 3-windshield: 4--glass; 5-pressing shape: 6-tightening: 7-locking device; 8-hinge pin Table 9
Remote alignment
Number of fasteners
Windshield! Window frame
Installation rigidity
Medical wall opening
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.