Marking for plastic packing products recycling

GB/T 16288-1996 Plastic packaging product recycling mark GB/T16288-1996 standard download decompression password: www.bzxz.net

GB/T 16288—1996
This standard is equivalent to the German standard DIN6120-1992 "Recycling Marking of Packaging Materials and Packaging Articles: Additional Labels for Plastic Packaging Materials and Packaging Articles".
The recycling mark for plastic packaging products specified in this standard is similar to the "recycling mark" designed by DIN6120 and the American Plastics Industry Association (SPI). It also has an equilateral triangle composed of three arrows, seven plastic codes and corresponding abbreviation codes. However, its scope of application is wider, not only applicable to plastic packaging products, but also to other plastic products. In addition, the content of this standard is also more comprehensive, adding specific chapters on the production, color, number and location of recycling marks for plastic packaging products. This standard was proposed by the China Light Industry General Association.
This standard is under the jurisdiction of the National Technical Committee for Standardization of Plastic Products. The drafting units of this standard are: Plastic Processing and Application Research Institute of China Light Industry General Association, Plastic Industry Office of China Light Industry General Association. The main drafters of this standard are: Cao Tongzhang, Liao Zhengpin, and Weng Yunxuan. 151
1 Scope
National Standard of the People's Republic of China
Marking for plastic packing products recycling
Marking for plastic packing products recycling This standard specifies the marking for plastic packaging products recycling and the method of indicating it. This standard applies to plastic packaging products and other plastic products. 2 Referenced standards
GB/T 16288-1996
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards are subject to revision, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T1844.1--1995 Plastics and resin abbreviations Part 1: Basic polymers and their characteristic properties GB7093.1--86 Graphic symbol representation rules General GB7093.4--86 Graphic symbol representation rules Graphic symbols for signs 3 Composition of plastic packaging product recycling marks
Plastic packaging product recycling marks are designed in accordance with the provisions of GB7093.1 and GB7093.4. The plastic packaging product recycling mark consists of a graphic, a plastic code and a corresponding abbreviation code. The graphic is an equilateral triangle with three arrows; 0 represents the material category as plastic, and the plastic code is a number composed of 0 and an Arabic numeral sequence number, located in the center of the graphic, representing different plastics; the plastic abbreviation code is expressed in accordance with the provisions of GB/T1844.1 and is located below the graphic, see Table 1, Figure 1. Table 1 Plastic name, code and corresponding abbreviation Plastic name
Plastic code
Plastic abbreviation code
High-density polyethylenewww.bzxz.net
Polyvinyl fluoride
Low-density polyethylene
Figure 1 Example of recycling mark for plastic packaging products
Approved by the State Administration of Technical Supervision on April 10, 1996 152
Polypropylene
Polystyrene
Others
Implemented on December 1, 1996
4 Dimensions of recycling mark for plastic packaging products
GB/T 16288--1996
Designed in accordance with the provisions of GB7093.4, it can also be reduced or enlarged according to relevant proportions according to actual needs. The color of the recycling mark for plastic packaging products
Generally black, other eye-catching colors can also be used, and it is required that it is not easy to fade or fall off. The molded ones can be the same color as the product. 6 The production of recycling marks for plastic packaging products
can be done by molding, printing or spraying, but the performance of the plastic packaging products should not be damaged. The number of recycling marks for plastic packaging products7
is generally one for each product, and should be increased if necessary. 8 The location of recycling marks for plastic packaging products should generally be located in a conspicuous place on the plastic packaging products, such as the front of the bag, the four sides of the box, the outside or bottom of the bottle (barrel). 153
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.