JB/T 3234-1999 Artificial diamond sintered body for wire drawing dies

JB/T 3234-1999 This standard is a revision of JB 3234-83 "Synthetic diamond sintered body for wire drawing dies". According to the requirements of GB/T 2828-1987 "Batch inspection counting sampling procedure and sampling table (applicable to continuous batch inspection)", the inspection and acceptance regulations have been revised, and other technical contents have not changed. This standard specifies the product code, shape and size, technical requirements, inspection rules and marking, and packaging of synthetic diamond sintered bodies for wire drawing dies. This standard is applicable to synthetic diamond sintered bodies synthesized by static pressure method for wire drawing dies. This standard was first issued on June 4, 1983. JB/T 3234-1999 Synthetic diamond sintered body for wire drawing dies JB/T3234-1999 Standard download decompression password: www.bzxz.net

ICS25.100.70
Machinery Industry Standard of the People's Republic of China
JB/T3234—1999
Synthetic diamond sintered body for wire drawing dies
Published on May 20, 1999
National Bureau of Machinery Industry
Implemented on January 1, 2000
JB/T3234—1999
This standard is a revision of JB323483 "Synthetic diamond sintered body for wire drawing dies". The original standard acceptance inspection adopts percentage sampling quantity. This standard is revised to be inspected and accepted in accordance with GB/T2828-1987 "Batch Inspection Count Sampling Procedure and Sampling Table (Applicable to Inspection of Continuous Batch)". Other technical contents are basically consistent with JB323483, and only re-edited according to relevant regulations.
This standard replaces JB323483 from the date of implementation. This standard is proposed and managed by the National Technical Committee for Standardization of Abrasives and Grinding Tools. The drafting unit of this standard: Zhengzhou Abrasives and Grinding Research Institute. The main drafter of this standard: Huang Xiangfen.
This standard was first issued on June 4, 1983. 1 Scope
Mechanical Industry Standard of the People's Republic of China
Synthetic Diamond Sintered Body for Wire Drawing Dies
JB/T3234—1999
Replaces JB323483
This standard specifies the product code, shape and size, technical requirements, acceptance rules and markings, and packaging of synthetic diamond sintered bodies for wire drawing dies.
This standard applies to synthetic diamond sintered bodies synthesized by static pressure method for wire drawing dies. 2 Referenced Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T2828-1987 Counting sampling procedures and sampling tables for batch inspection (applicable to inspection of continuous batches) GB/T3235-1999 Determination method of wear ratio of artificial diamond sintered body 3 Product code
Code for artificial diamond sintered body for wire drawing die: JRS-SJR
Shape and size
Sintered body for wire drawing die
Artificial diamond
The shape of artificial diamond sintered body for wire drawing die is cylindrical, and its main dimensions are shown in Table 1. Table 1
Outer diameter D
Thickness H
Maximum aperture d
Note: The numbers in brackets are for ring-set products. www.bzxz.net
5 Technical requirements
Outer diameter and thickness deviation of artificial diamond sintered body for wire drawing die, see Table 2. Approved by the State Bureau of Machinery Industry on May 20, 1999100
Implementation on January 1, 2000
Basic dimensions
Outer diameter D
JB/T3234-1999
Limit deviation
2 Parallelism of artificial diamond sintered body for wire drawing die shall not exceed 0.1mm. 5.2
Artificial diamond sintered body for wire drawing die shall not have cracks and edge loss5.3
The wear ratio of artificial diamond sintered body without satin firing shall be in accordance with the provisions of Table 3. 5.4
Basic size
45-120
Thickness H
Limit deviation
Single grain wear ratio
≥40×10
≥60×103
≥100×103
5.5The particle size of diamond micropowder used in artificial diamond sintered body shall not exceed 40m. Test method
The size shall be measured with a vernier caliper with a graduation value of 0.02mm. Appearance inspection shall be carried out with a 20x magnifying glass with scale and parallelism inspection shall be carried out with a vernier caliper for symmetry inspection. 6.3
The wear ratio shall be determined in accordance with the provisions of JB/T3235. 7 Acceptance rules
Product delivery inspection shall be carried out batch by batch in accordance with the technical requirements of this standard, and qualified products shall be accompanied by a certificate of conformity. The number of packaged particles is used as the "inspection batch" of the product, and a normal inspection sampling plan is implemented according to the provisions of GB/T2828. 7.2
7.2.1 Inspection level
The basic dimensional deviation, appearance, and parallelism inspection adopt the "general inspection level II". 7.2. 1. 1
2 The inspection of wear ratio adopts the "special inspection level S-3". 7.2. 1.2
7.2.2 The acceptable quality level (AQL) is 2.58 Marking and packaging
The following markings must be on the outer packaging:
a) Product name;
b) Manufacturer;
c) Product mark;
d) Registered trademark;
e) Packaging quantity;
D Production date or batch number.
JB/T3234-1999
The packaging should be accompanied by a certificate of conformity, which should indicate: 8.2
a) Product name;
b) Product model or specification:
c) Quantity, batch number:
d) Inspection stamp.
The product can be packed in double-layer plastic bags, with the certificate of conformity placed between the two layers. 8.3
8.4The product should be packed in 10, 20, 50, 100, 200, 500, and 1000 pieces respectively. 8.5
The packaging should be beautiful and firm to ensure easy carrying. 3
Mechanical Industry Standard
Synthetic Diamond Sintered Body for Wire Drawing Dies
JB/T3234—1999
Published by the Machinery Standardization Research Institute of the Ministry of Machinery Industry Printed by the Machinery Standardization Research Institute of the Ministry of Machinery Industry (No. 2 Shouti South Road, Beijing: Postal Code 100044)*
Format 880×12301/16 Printing Sheet 1/2 Number of Words 8000 First Printing in September 1999
First Edition in September 1999
Print Quantity 1-500
Price 500 Yuan
99-559
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.