JB/T 2216-1999 Pole coil hydraulic press types and basic parameters

This standard specifies the types and basic parameters of pole coil hydraulic presses. This standard is applicable to pole coil hydraulic presses. This standard serves as the basis for the design and selection of pole coil hydraulic presses for hydro-generators, phase regulators, synchronous motors, DC motors, and DC traction motors for pole coil shaping and hot pressing processes. JB/T 2216-1999 Types and basic parameters of pole coil hydraulic presses JB/T2216-1999 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T2216
Shu Lu Sui
The type and basic data of the magneto coll1999-08-06
Wa Xian Ji Dong
2000-01-01
JB/T2216
This standard is a revision of JB 2216-81 based on the provisions of Chapters 4, 5, and 6 of GB/T 1.1-1993 and Chapter 5 of GB 1.3--1997.
This standard replaces B2216-81 from the date of implementation. This standard was proposed by Shenyang Electrician Special Equipment Research Institute. This standard was drafted by Shenyang Electrician Special Equipment Research Institute. The main drafter of this standard: Chen Jiashan.
This standard was first issued on October 1, 1981, and is subject to revision. This standard is entrusted to Shenyang Electric Special Equipment Research Institute for interpretation. 1
1 Scope
Chicken cheek Kui Lu Wa Yi Xian
Lamp Meow Mold Contains
Xiao Sui Group
The type and basic data of the magneto collThis standard specifies the type and basic parameters of the magneto coll oil press. This standard is applicable to magneto coll oil press. 1999
JB/T2216
JB221681
This standard is used as the basis for designing and selecting magneto coll oil presses for magneto coll shaping and hot pressing processes of hydro-generators, mixers, synchronous motors, DC motors, and DC traction motors. 2 Types
2.1 Top-pressure magnetic pole coil hydraulic press:
Its structure consists of three beams and four columns, a trolley-type movable workbench, a cylinder and a side pressure system. The movable crossbeam moves downward to pressurize the workpiece (see Figure 1)
Figure 1 Top-pressure
2.2 Downward-pressure magnetic pole coil press.
Its structure consists of three beams and four columns, a trolley-type movable workbench and a vertical hydraulic press. Its movable crossbeam moves from bottom to top to achieve pressurization of the workpiece (see Figure 2)
Wa Jiman1999-08-06Tumor
2000-01-01Small Cable
3 Basic parameters of magnetic pole coil hydraulic press
JB/T22161999www.bzxz.net
Figure 2 The basic parameters of the downward pressure
magnetic pole coil hydraulic press should comply with the provisions of Table 1. Table 1
Pressure adding method
Nominal pressure N
Maximum lifting distance of workbench
Workbench lifting and lowering distance
Distance from trolley work surface to
Workbench surface mm
Effective trolley work surface
Nominal pressure (single pressure measurement) KN
Piston working stroke
Pressure head
Maximum distance of pressure head
Downward pressure type
2×500
3×500
6 x 500
7× 500 9×450
Chicken cheek Xinkui porcelain
Meow mold kite
Cutting heron owl navigation matrix
JB/T2216
Hang 880b1230
19XXXX Ridge
100044
Wan Duan X/X
Travel XXX,XXX
19XX Collection XX Cabin
Leng X Dai
German pxXX.XX Wing
Xian Ji Lotus Snapper
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.