JB/T 6632-1993 Filters for mechanical sealing systems

This standard specifies the type, basic parameters, model representation method, main technical requirements, inspection, packaging, etc. of filters for mechanical seal systems. JB/T 6632-1993 Filters for Mechanical Seal Systems JB/T6632-1993 Standard download decompression password: www.bzxz.net

Machinery Industry Standard of the People's Republic of China
JB/T 6632-1993
Filters for Mechanical Seal Systems
Published on 1993-05-07
Ministry of Machinery Industry of the People's Republic of China
Implemented on 1994-01-01
Mechanical Industry Standard of the People's Republic of China
Filters for Mechanical Seal Systems
1 Subject Content and Scope of Application
JB/T 6632-1993
This standard specifies the type, basic parameters, model representation method, main technical requirements, inspection, packaging and other contents of filters for mechanical seal systems.
This standard applies to filters for mechanical seal systems. 2 Reference standards
GB4753 Technical conditions for cast aluminum nickel cobalt permanent magnet (hard magnetic) alloy 3 Types and basic parameters
3.1 Types
Filters for mechanical seal systems are divided into two types: GL type is filter screen (see Figure 1); GC type is magnetic ring plus filter screen (see Figure 2). The pressure bearing direction is unidirectional and bidirectional. (00002
1O-type seal diagram:
2-cylinder pin:
6-sealing pad:
1993-05-07 approved by the Ministry of Machinery Industry
7-screw:
Filter structure diagram (filter screen type)
3-filter screen:
8-filter cover;
4-0-type seal ring:
9-middle ring:
5-exhaust bolt:
10-filter body
1994-01-01 implemented
3.2 Basic parameters
1-0-type seal ring:
5-spring:
JB/T 6632-1993
Figure 2 Filter structure
2-Cylindrical pin:Www.bzxZ.net
6-Exhaust bolt:
10-Intermediate ring:
Rated pressure: 1.6MPa
Rated temperature: 150℃
Filter accuracy: 50um
Interface size: Rp1/2
4-Model indication method
11-Magnetic ring:||t t||100μm
3-Filter net:
7-Sealing pad;
12-Pad:
4-0-type sealing ring:
8-Screw:
13-Screw:
Indicates the interface thread size
9-Filter cover:
14-Filter body
Use numbers to indicate the filtering accuracy, μm
Use D to indicate one-way Pressure-bearing, indicated by S Bidirectional pressure-bearing GL Filter filtration, indicated by GC Magnetic ring plus filter filtration Rated pressure 10MPa
Model example:
JB/T6632-1993
Magnetic filter with rated pressure of 6.3MPa, filtration accuracy of 100μm, and interface size of Rp1/2: 63GCD100/Rp1/2
Main technical requirements
Filters for mechanical sealing systems shall comply with the provisions of this standard and be manufactured according to drawings and technical documents approved by the prescribed procedures. The materials of magnetic filters are shown in the table below.
Parts name
Filter body and filter cover
1Cr18Ni9Ti
O-ring
Fluororubber
Polytetrafluoroethylene
Other parts
0Cr1 8Ni9, 1Cr18Ni9
In the assembly of magnetic filters, magnetic rings are sucked together in pairs, and each pair is separated by a pad. The two separated pairs should be installed in a repulsive manner. 5.4
The products are subjected to water pressure test one by one before leaving the factory. When the pressure difference between the filter and the front and rear exceeds 0.05MPa during use, it should be cleaned. 5.5
The technical requirements of magnetic rings shall comply with the provisions of GB4753. 6
Inspection method
After assembly, the liquid outlet is blocked with a plug, and the liquid inlet is pressurized (pay attention to exhaust when pressurizing), pressurized to the standard value, and maintained for at least 5 minutes. During this period, the pressure gauge display is not allowed to drop and no liquid seeps out. Marking, packaging, transportation and storage
The filter is packed in wooden boxes or corrugated paper when leaving the factory, and can prevent damage during transportation. The product should have a product logo. The product model, name and relevant parameters should be indicated on the logo. 7.2
7.3 Products should have product certificates. The certificate should indicate the product model, name, manufacturer, production date and the signature of the inspector. Products should be stored in a clean and dry warehouse. 7.4
Additional instructions:
This standard was proposed and managed by the Hefei General Machinery Research Institute of the Ministry of Machinery Industry. This standard was drafted by the Shenyang Mechanical Seals Research Institute. The main drafters of this standard were Shi Xueli and Cao Hongqin. 3
People's Republic of China
Mechanical Industry Standard
Filters for Mechanical Sealing Systems
JB/T 66321993
Published and issued by the China Academy of Mechanical Science
Printed by the China Academy of Mechanical Science
(No. 2 Shouti South Road, Beijing
Postal Code 100044)
Format 880×12301/16
Word Count 6.000
Sheet 1/2
First Edition in October 1993
First Printing in October 1993
Print Quantity 1-500
Price 2.00 Yuan
Mechanical Industry Standard Service Network: http://www.JB.ac.cn99
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.