JB/T 2648.2-1995 Technical requirements for blades of bulldozers, scrapers and graders

This standard specifies the marking, technical requirements, test methods, inspection rules and marking, packaging, storage, etc. of bulldozer, scraper and grader blades. This standard applies to bulldozer, scraper and grader blades. JB/T 2648.2-1995 Technical requirements for bulldozer, scraper and grader blades JB/T2648.2-1995 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T2648.2
Mipengke
Addiction Snake
1995-06-20
Jia Kuiji
1996-01-01
JB/T2648.21995
This mechanical industry standard for blades and bolts for bulldozers, scrapers and graders includes the following parts: Part 1 (i.e. JB/T2648 .1): Main shapes and basic dimensions of blades: Part 2 (i.e. JB/『2648.2): Technical requirements for blades: Part 3 (i.e. JI3/『2648.3): Bolts for blades Part 1 of the standard is formulated based on the international standard ISO71291989 "Upper machinery - Pushers, transporters and graders - Blades: Main shapes and basic dimensions" drafted by the International Organization for Standardization IS0/TC127 Earthmoving Machinery Technical Committee. The technical content is equivalent to the international standard.
Part 3 of the standard, the section on the shape and dimensions of screw rods for blades, is based on the international standard ISO71291989 "Upper machinery - Pushers, transporters and graders - Blades: Main shapes and basic dimensions" drafted by the International Organization for Standardization IS0/TC127 Earthmoving Machinery Technical Committee. The technical content is equivalent to the international standard. Appendix A in Part 3 is the standard appendix. This standard shall be implemented from January 1, 1996, and replace JB2648-81 at the same time. This standard was proposed and coordinated by Tianjin Engineering Machinery Research Institute of the Ministry of Machinery Industry. Part 1 and Part 2 of this standard were drafted by Tianjin Engineering Machinery Research Institute of the Ministry of Machinery Industry; Part 3 of this standard was jointly drafted by Tianjin Engineering Machinery Research Institute of the Ministry of Machinery Industry and Shenyang Screw Factory. The main drafters of this standard are Wu Runcai, Yang Yuyi, and Shenyang Screw Factory. 1 Scope
JB/T2648.21995
This standard specifies the marking, technical requirements, test methods, inspection rules and marking, packaging, storage, etc. of blades for pushers, scrapers and flat machines.
Applicable to the blades of bulldozers, scrapers and levelers. 2 Reference standards
The provisions contained in the following standards constitute the provisions of this standard for the purpose of application in this standard. When this standard is completed, the versions shown in the following standards are considered to be valid. All standards are subject to revision. The parties to this standard should explore the possibility of using the latest version of the following standards. CB 22887
GB 229:84
GB 282887
J3/T 2648.1—95
3 Dimensions and markings
Metal tensile test method
Metal Charpy (U-notch) punch-out test piece batch inspection counting sampling procedure and throwing table (applicable to continuous batch inspection) The main shape and basic shape of the blades of bulldozers, scrapers and levelers! 3.1 The size specifications of the blade shall be in accordance with the provisions of JB/T 2548.1 and shall be marked as follows. JL/T 2648.2-95
Number
Blade length
Blade thickness
Blade width
Blade name (for pusher, shovel, and scraper) 3.2 Marking example:
Thickness 25mm, thickness 25mm, length 762mm for pusher blade: Pusher blade 254 25 7G2 JB/T 2G48. 2-954 Technical requirements
The mechanical properties and hardness of pusher and scraper blades are recommended to be in accordance with the provisions of Table 1. Table 1
Tensile strength.
1995-06-20
Elongation
Zhong Shirenak
J/err2
-16~52HRC
1996-01-01Small cable
JB/T2648.2
4.2The heat treatment requirements for small blades of graders are recommended to be in accordance with the provisions of Table 2. Table 2
Heat treatment method
Blade thickness mm
Minimum quenching width
Heat treatment requirements
Deepness of tarnish layer
Surface quenching
4--5GHRG
4.3The blade surface is not allowed to have cracks, scars, curling and other defects that affect the use. 4.4After the bolt hole of the small blade is squared, the protrusion around the square hole shall not exceed 0.3mm. The back error of bulldozer and scraper blades should be within the flatness tolerance, and the flatness tolerance is calculated as follows: 4.
1 - 3. 7 X
tt||Flatness tolerance: mm;
Blade length. mm.
4. The surface of the blade should be primed, and the paint color is determined according to the requirements of the unit in use. 5 Test methods and inspection rules
Overall
5.1 The tensile test of the mechanical properties of the bulldozer and scraper blades shall be carried out according to the No. 12 test method specified in D228; the impact test shall be carried out according to the standard test specimens and test methods specified in GB229. The location of the pulling and punching test specimens is shown in Figure 1 (no less than 3 specimens), and the location of the hardness test is shown in Figure [. The sampling position of the punch sample should be between 2 and 12 mm from the surface, and the hardness test should be carried out at three locations, about 103 mm from the center of the two ends. The sampling of the sample should be carried out at the same time (the sampling center is about 8 mm from the surface). 5.2 The hardness test of the machine blade should be carried out at two locations along the length, at both ends and in the middle. For surface quenching, three points should be measured at each location, and for overall quenching, five points should be measured at each location. The measurement points should be evenly distributed along the width of the blade. 5.3 Inspection The blade should be inspected by the inspection department of the manufacturer according to this standard and have a certificate of conformity. 5.4 The factory inspection of the blade should be carried out in accordance with the provisions of GB 2828. The inspection batch, sampling plan, inspection level and qualified quality level (AQL) shall be determined by the quality inspection department of the production (or) by itself or by the production (or) by negotiation with the user department. 2www.bzxz.net
6 Marking, packaging and storage
JB/T2648.2
6.1 The blade should be printed with a logo or trademark (identification), and the logo and trademark (identification) should be clear. 2 The blade shipping package can be tied with straw rope and wire or fastened with a metal screw with a pattern. The binding should be firm and not loose. 6.3 The blade should be stored in a moisture-proof warehouse. Under normal circumstances, the manufacturer should ensure that it will not rust within one year after leaving the factory. 3
睛880b1230
1996桌1舱
100044
黛段3/4
1996巢1舱轮干黛
飚10.00翼
为的值1
芃鱻极匙煤
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.