JB/T 9740.1-1999 Low speed wind turbine series

JB/T 9740.1-1999 This standard is a revision of NJ 350-85 "Low-speed Wind Turbine Series". During the revision, the wording and values ​​of "speed limit mode" and "wind speed" were modified. This standard applies to multi-blade horizontal axis wind turbines with a blade tip speed ratio of less than 2. This type of wind turbine is mainly used to drive some water-lifting equipment and can also be used as a power source for other equipment. This standard was first issued on March 5, 1985. JB/T 9740.1-1999 Low-speed Wind Turbine Series JB/T9740.1-1999 Standard download decompression password: www.bzxz.net

ISC27.180
Machinery Industry Standard of the People's Republic of China
JB/T 9740.1~9740.4—1999
Low speed wind turbine
Lw speed wind energy conversion system1999-08-06 Issued
National Machinery Industry Bureau
2000-01-01 Implementation
JRT9740.1—1999
This standard is a revision of N350—85 "Low speed wind turbine series". The main contents of the revision: "Standard high speed performance" will be changed to "tip speed ratio" and "rated wind speed 8m/g" will be changed to "design wind speed 6-9m/s". The value of "Speed ​​limit type: wind wheel deviates from wind direction" is changed to "wind turbine should have reliable tracking device" and added - other equipment matching with the wind turbine, refer to the corresponding standard". This standard replaces NJ35085 from the date of implementation. Appendix A of this standard is the appendix of the standard. Appendix B and Appendix C of this standard are both informative appendices. This standard is part of the JB 974 "Low Speed ​​Wind Turbine" series of standards, which includes the following parts: JB/F9740.1w-199y
Low Speed ​​Wind SerieswwW.bzxz.Net
Non-[Light 40. 11999 Types and basic parameters of low-speed wind turbines JB/『9740.3—1999 Technical specifications for low-speed wind turbines [B/9740.4—1999 Specifications for low-speed wind turbines The standard is proposed and managed by the Technical Committee for the Promotion of Wind Turbines. The drafting unit of this standard is Hohhot Animal Husbandry Machinery Research Institute. The main drafter of this standard is Bai Zhile. This standard was first published on March 5, 1985. Scope
Machinery Industry Standards of the People's Republic of China
Low-speed wind turbines
Seriesfor Jow sperlwind rarrgy conversion system JB/T9740.1—1999
代带85
This standard is applicable to multi-blade horizontal axis wind turbines with blade tip speed ratio less than 2. This type of wind turbine is mainly used to drive some water lifting equipment and can also be used as the power of other equipment.
2 Wind wheel diameter series
2.6. 2.5. 3.2, 4.0, 5.0, 6.0. 8.0. Ju.Um.3 Rated design wind speed
6~9m/s
1 Speed ​​limit device
The wind turbine should have a reliable speed limit device,
5 And the lower limit value of the tower height is calculated according to formula 1.1) HhcD/2
Formula: H Tower height, m:
Force - The height of obstacles close to the wind turbine, m: the distance from the obstacle to the lowest point of the wind turbine, m: D--the diameter of the wind turbine, m.
The tower height series to be promoted (calculated from the ground): 6, 7, 9, 10, 2, 14, 1s, [8, 21m. 6 Piston pump cylinder diameter
The diameter series used with low-speed wind turbines [see Appendix A (standard series)? Active pump piston stroke
The piston stroke series used with low-speed wind turbines is shown in Appendix B (shown in Appendix B): 8 Wind turbine active pump plastic matching performance
Low wind turbine-piston unit matching performance is shown in Appendix C (shown in Appendix C)" Matching performance
Other equipment used with wind turbines shall comply with the corresponding standards. Approved by the State Machinery Industry Bureau on August 6, 1999 and implemented on January 1, 2000 ||tt ||JE/F9740.1-1999
Appendix
(Standard Appendix)
Huojisan Pump Diameter Series
Piston Diameter Series for Low-speed Wind Turbine: 45.50.55.60.70.80.90,100,110,120,160.200,250,320,400,500mm. Appendix B
(Reminder)
Huojisan Piston Stroke Series
Piston Diameter Series for Low-speed Wind Turbine: (75).100.120.140.160,180,210.240,270mm See Table B1 for the matching relationship between low-speed wind turbine and Huojisan Pump Unit. Table
hole head white connection drive pull this frequency
piston reciprocating area
vertical shaft transmission received under the reverse box
night indicates the total variety:
a table records the variety of research and design:
a·Indicates the products that have been designed and produced
Indicates the special flavor supplied products and:
2 The areas in brackets may be
JBT9740.1-1999
JB/T9740.1-1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.