JB/T 2001.63-1999 Filters for water system pumping stations (PN=31.5MPa)
time:
2024-08-12 07:57:44
- JB/T 2001.63-1999
- in force
Standard ID:
JB/T 2001.63-1999
Standard Name:
Filters for water system pumping stations (PN=31.5MPa)
Chinese Name:
水系统 泵站用过滤器(PN=31.5MPa)
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-06-28 -
Date of Implementation:
2000-01-01
Standard ICS number:
Fluid systems and general parts >> 23.100 Fluid power systemsChina Standard Classification Number:
Machinery>>General Parts>>J20 Hydraulic and Pneumatic Devices
alternative situation:
JB 2066-1984
Focal point Organization:
Metallurgical Equipment Standardization Technical CommitteePublishing Department:
Metallurgical Equipment Standardization Technical Committee
Skip to download
Summary:
JB/T 2001.63-1999 This standard is a revision of JB 2066-84 "Filters for hydraulic pump stations (Pg=31.5×100000Pa)". This standard specifies the type, size and technical requirements of filters. This standard applies to filters that play a coarse filtration role in high-pressure pipelines of water pump stations with a nominal pressure of 31.5MPa. This standard was first issued in 1984. JB/T 2001.63-1999 Filters for water system pump stations (PN=31.5MPa) JB/T2001.63-1999 Standard download decompression password: www.bzxz.net
Some standard content:
IC.s$ 23.110
Standard of the Machinery Industry of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts1999-06-28 Issued
State Machinery Industry Bureau
2(-01-U1 Implementation
Standard of the Machinery Industry of the People's Republic of China
Filter for water system pump station
WatersygtemFllterfotwateraccumtlator(PN=31.5 MPa ]
This standard specifies the type, size and technical requirements of filters. JB/T2001.63-1999
JB2366-84
4 Applicable to the filter with nominal pressure of 3.MPa. 2. Type and size
The type and size of the filter shall be in accordance with the provisions of Figure 1 and the table. 1: 2-: Figure 4: 5
G-core: 7-flow: 8-connecting flange, 9-water meter: 10-radiator Approved by the State Machinery Industry Bureau on June 28, 1999, and implemented on January 1, 2000bZxz.net
IB: 21m 57
JB20U1.53.2
:w: 2nm1 63.3
iB/T 200:.53.4
I : 615
JB.T 200:.53 6
B20U1 5J.1
JB 20: 63 3
IB-T 200:.63.4
2001.63.3
B/: 2001 .63 6
JR/T 2901.37
5 technical requirements
1-2 # 18
127×22
132×25
219×35
273*45
JB/T2001.63—1999
3.1 Nominal force 31.5MPu, test force 42MPa19
Guaranteed Kmn, cellar and shell are not cross-sea and drop! Late phenomenon. 3.2 Before assembly, fill the test amine on the potential sand must be corrected to remove the impact. 4 Marking example
Number of 65mm approx. through the end:
Filter UN6JB/T200:.63
Quantity 1999
4 xM3G
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Standard of the Machinery Industry of the People's Republic of China
JB/T 2001.1~2001.74—1999
Water system assembly and parts1999-06-28 Issued
State Machinery Industry Bureau
2(-01-U1 Implementation
Standard of the Machinery Industry of the People's Republic of China
Filter for water system pump station
WatersygtemFllterfotwateraccumtlator(PN=31.5 MPa ]
This standard specifies the type, size and technical requirements of filters. JB/T2001.63-1999
JB2366-84
4 Applicable to the filter with nominal pressure of 3.MPa. 2. Type and size
The type and size of the filter shall be in accordance with the provisions of Figure 1 and the table. 1: 2-: Figure 4: 5
G-core: 7-flow: 8-connecting flange, 9-water meter: 10-radiator Approved by the State Machinery Industry Bureau on June 28, 1999, and implemented on January 1, 2000bZxz.net
IB: 21m 57
JB20U1.53.2
:w: 2nm1 63.3
iB/T 200:.53.4
I : 615
JB.T 200:.53 6
B20U1 5J.1
JB 20: 63 3
IB-T 200:.63.4
2001.63.3
B/: 2001 .63 6
JR/T 2901.37
5 technical requirements
1-2 # 18
127×22
132×25
219×35
273*45
JB/T2001.63—1999
3.1 Nominal force 31.5MPu, test force 42MPa19
Guaranteed Kmn, cellar and shell are not cross-sea and drop! Late phenomenon. 3.2 Before assembly, fill the test amine on the potential sand must be corrected to remove the impact. 4 Marking example
Number of 65mm approx. through the end:
Filter UN6JB/T200:.63
Quantity 1999
4 xM3G
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- JB/T 9933.2-1999 Accuracy test of small module gear hobbing machine
- JB/T 8486.2-1996 Technical requirements for CNC universal tool milling machines
- GB/T 5211.1-2003 Determination of water-soluble matter in pigments - Cold extraction method
- GB/T 8639.4-1988 Chemical analysis of vanadium - O-phenanthroline photometric method for the determination of iron content
- GB/T 24040-1999 Principles and framework for life cycle assessment of environmental management
- GB/T 5009.184-2003 Determination of thiamethoxam residues in grains and vegetables
- QB/T 3638-1999 Leather ball industry terminology
- CB 3556-1993 General technical requirements for acoustically transparent rubber for underwater acoustic transducers
- GB/T 33694-2017 Specification observating for automatic climatological station
- JB/T 7952-1995 Air Purifier
- GB/T 4511.3-1984 Determination of pseudo relative density and total porosity of coke
- JB/T 8364.3-1996 Technical specification for 60° tapered pipe thread taps
- HY/T 055-2001 Pleated cartridge microfiltration core
- GB 17741-1999 Technical specification for earthquake safety assessment of engineering sites
- GB/T 4334.3-2000 Test method for corrosion of stainless steel by 65% nitric acid
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail:wymp4wang@gmail.com