JB/T 10231.13-2002 Tool product testing methods Part 13: Saw blades and milling cutters

This part specifies the inspection methods and inspection instruments for finished products of saw blade milling cutters and screw slot milling cutters. These methods are not exclusive. This part is applicable to the inspection of saw blade milling cutters and screw slot milling cutters produced in batches according to GB/T 6120, GB/T 6121 and JB/T 8366. JB/T 10231.13-2002 Tool product inspection methods Part 13: Saw blade milling cutters JB/T10231.13-2002 Standard download decompression password: www.bzxz.net

ICS15.100.20
Machinery Industry Standard of the People's Republic of China
JB/T10231.13—2002
Testing methods for cutting tool products
Part 13: Saw blades and milling cutters
Tuulinspaction methods
Part13:Metal slitting saws
Published on 2002-07-16
Implemented on 2002-12-01
Published by the State Economic and Trade Commission of the People's Republic of China
Quality reference documents
Inspection basis
Find roughness
Circular runout,
Inspection location
Testing method
Testing equipment
Thickness and: working part Diameter
Forward tilt, rear angle
Detection part...
Detection method
Detector, tool
Detection part
Inspection method
Detection tool
Surface treatment
JB/T10231.13—2002
This standard is issued by China Machinery Industry Federation
This standard is approved by the National Standardization Technical Committee. This standard was drafted by Beijing Tool Factory, and the main drafter of this standard is Wang Shuzai.bzxZ.net
JB/T10231.13-2002
1 Scope
Testing methods for power tools
Part 13: Saw blades and milling cutters
JE/10231.132002
This part currently defines: Testing methods and convenient detectors for finished product testing of saw blades, drills, and nails. These methods are not effective.
- This part applies to GBT6120, GET6121, BT8366, and the test methods for mass-produced saw blades, milling cutters, and screwdrivers. 2 Normative references
The following normative clauses become clauses of this part through reference to this part of the standard. For all referenced documents with a date, all subsequent revisions (excluding errata) or revisions are not applicable to this part. However, the customer who has reached a design based on this part is encouraged to study whether the latest version of this document can be used. For all referenced documents with a date, the latest version applies to this part. G/1201996 Milling cutter model and dimensions (EVIS229:972) G612--[96 standard technical conditions] JB3661996 Screw thread cutting JB1231.1-2001 Product testing method Part 1: General 3 Testing basis Related product specifications and drawings 4 Appearance According to the provisions of B/T1023:.1-2004 Article 4 5 Surface torsion properties According to the provisions of B/T10231.1-2001 Article 6 Runout 6.1 Testing location 6.1.1 The radial runout of the circumferential blade to the inner hole of the milling cutter and the screw thread cutting tool (the center of the thickness L) 61.2 Side runout of the end face facing the inner hole axis For saw blade milling cutter, side follower face of milling cutter close to the tooth grip, 6.2 Inspection method
6.2.1 Radial runout of the circumferential cutting edge to the inner hole axis Figure 1, install the saw blade milling cutter or screw groove on the boss core shaft (the core shaft and the cutter inner hole should be matched), place the dynamic measuring instrument on both sides, and the indicator probe vertically touches the inspected part, rotate the core shaft, and the cutter rotates one circle. The difference between the maximum and minimum values ​​of the indicator pointer is read as the rotation runout, and the maximum value of the absolute value of the difference between adjacent inner holes is taken as the adjacent inner hole runout value. 6.2.2 Side runout of the end face facing the inner hole axis Figure 1, install the saw blade milling cutter or screw groove on the boss core shaft (the core shaft and the cutter inner hole should be matched), and use the dynamic measuring instrument JB/T 10231.13—2002
The measuring head of the indicator shall directly touch the part to be inspected, the mandrel shall be rotated, the cutter shall rotate a circle, the maximum value of the difference between the maximum and minimum readings of the indicator gauges on the two end blades shall be taken as the surface runout value, and the maximum value of the difference between the adjacent potential difference values ​​on both sides of the free blades shall be taken as the circular runout value of the adjacent teeth. Figure
6.3 Pre-inspection tool
) The graduation value is 0.01n indicator gauge or 0.001mn lever indicator gauge. h) Magnetic hanger:
c) Boss shaft
d) Runout tester:
e) Cast iron plate
? The milling thickness and the outer diameter of the working part shall be in accordance with the provisions of 10.2 of JB/T10231.1-2001. The inner hole of B shall be in accordance with the provisions of chapter 1 of JB/T10231.J2001. 9 Angle, back angle 9.1 Testing location The front and back of the circular teeth of the lead cutter and screw milling cutter. 9.2 Testing method 9.2.1 Front angle See Figure 2. Place the working surface of the angle support ruler against the adjacent tooth top of the effective cutter tooth, adjust the measuring tool so that the workpiece surface of the front angle ruler is in contact with the tooth to be measured, and make the working surface of the back ruler contact with the tooth of the cutter tooth, and then the front angle value can be read. 92.2 Back angle
See Figure 2, place the lower working surface of the angle support ruler against the adjacent tooth of the measuring cutter tooth, adjust the measuring tool so that the lower proof of the back angle ruler is in contact with the back force of the measuring cutter tooth, and make the front angle ruler working surface contact with the top of the measured cutter tooth, then the back angle value can be read, set: when there is a dispute, put it on the universal tool under the microscope, 9.3 Check the book tool
multi-blade angle ruler "division value 2), universal tool microscope 10 tunnel angle
10.1 Inspection position
the side clearance of the screw lamp staggered blade (about at the clamping diameter). 10.2 Inspection method
JB/T10231.132002
See Figure 3 for the back angle inspection. When testing on the special measurement, place the knife level on the special test seat for the side angle, press the indicator on the effect to take the value, and measure at 2 to 3 approximately equal positions. Take the smallest value of the indication these times, which is the value of the tread angle. Use the same method to measure the value of the side clearance angle of the other side, and take the smallest value of the indicator readings on the two end surfaces as the side clearance value. [Surface: 2 Positioning grain: 3
Opening the same as the dovetail screw M6×12: 4—Small hexagonal correction ×25; 5 Figure
Indicator original
JB/T10231.132002
10.3 Testing equipment
Special inspection tool for chipping angle: Indicator with a graduation value of 0.01mm, 11
According to the provisions of Chapter 11 of JB/T10231.1—2001, 12 Marking
According to the provisions of Chapter [3 of J/T10231.1-2001: Packing
According to the provisions of Chapter 14 to JB/T10231.1——2001, : 14 Surface treatment
According to the provisions of Chapter 15 of JB/T10231.1200. +
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.