AS NZS 3500.0 2003 Plumbing and drainage Part 0 Glossary of terms

STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND

Australian/New Zealand Standard

Plumbing and drainage

Part 0: Glossary of terms

6

AS IS

内部资料

仅供参考

张忠辉惠存

禁止一切非法目的和活动行为，否则后果自负。

NOT FOR PUBLIC RELEASE

2

AS/NZS 3500.0:2003

This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee WS-014, National Plumbing and Drainage Code. It was approved on behalf of the Council of Standards Australia on 18 September 2003 and on behalf of the Council of Standards New Zealand on 12 November 2003. It was published on 15 December 2003.

The following are represented on Committee WS-014:

• ACT Department of Urban Services
• Association of Hydraulic Services Consultants Australia
• AUSTAP
• Australian Building Codes Board
• Australian Industry Group
• Brisbane Water
• Building Industry Authority NZ
• Building Officials Institute of New Zealand
• Building Research Association of New Zealand
• Business New Zealand
• Certification Bodies (Australia)
• Department of Human Services (South Australia)
• Department of Infrastructure, Energy and Resources (Tasmania)
• Department of Infrastructure, Planning and Environment (NT)
• Department of Land and Water Conservation NSW
• Department of Local Government and Planning (Queensland)
• Fire Contractors Federation
• Gas Appliance Manufacturers Association of Australia
• Housing Industry Association
• Institute of Plumbing Australia
• Master Builders Australia
• Master Plumbers, Gasfitters and Drainlayers New Zealand
• National Association Sanitary Plumbing and Drainage Contractors
• New Zealand Water and Waste Association
• Plastics Industry Pipe Association of Australia
• Plumbers, Gasfitters and Drainlayers Board
• Plumbing Industry Commission
• South Australian Water Corporation
• Sydney Water Corporation
• Water Corporation Western Australia

Keeping Standards up-to-date

Standards are living documents which reflect progress in science, technology and systems. To maintain their currency, all Standards are periodically reviewed, and new editions are published. Between editions, amendments may be issued. Standards may also be withdrawn. It is important that readers assure themselves they are using a current Standard, which should include any amendments which may have been published since the Standard was purchased.

Detailed information about joint Australian/New Zealand Standards can be found by visiting the Standards Australia web site at www.standards.com.au or Standards New Zealand web site at www.standards.co.nz and looking up the relevant Standard in the on-line catalogue.

Alternatively, both organizations publish an annual printed Catalogue with full details of all current Standards. For more frequent listings or notification of revisions, amendments and withdrawals, Standards Australia and Standards New Zealand offer a number of update options. For information about these services, users should contact their respective national Standards organization.

We also welcome suggestions for improvement in our Standards, and especially encourage readers to notify us immediately of any apparent inaccuracies or ambiguities. Please address your comments to the Chief Executive of either Standards Australia International or Standards New Zealand at the address shown on the back cover.

This Standard was issued in draft form for comment as DR 03066.

3

Australian/New Zealand Standard™

AS/NZS 3500.0:2003

Plumbing and drainage

Part 0: Glossary of terms

Originated as AS 1355—1979.

Previous edition AS/NZS 3500.0:1995.

Third edition 2003.

COPYRIGHT

© Standards Australia/Standards New Zealand

All rights are reserved. No part of this work may be reproduced or copied in any form or by any means, electronic or mechanical, including photocopying, without the written permission of the publisher.

Jointly published by Standards Australia International Ltd, GPO Box 5420, Sydney, NSW 2001 and Standards New Zealand, Private Bag 2439, Wellington 6020

ISBN 0 7337 5524 0

4

PREFACE

This Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee WS-014, National Plumbing and Drainage Code, to supersede AS 3500.0—1995, National Plumbing and Drainage Code, Part 0: Glossary of terms.

This revision of this Standard has been develop to complement the Plumbing Code of Australia and incorporates amendments and additions arising from industry requirements.

This Standard is part of a series, under the title Plumbing and Drainage, as follows:

The Standard is primarily intended for the general water industry and for use in the interpretation of terminology used in the various parts of the Plumbing and drainage series of Standards and covers water supply from the reticulation main into the premises, including hot water service systems, sanitary fixtures, drainage and their associated water and waste fittings, pipe systems and associated components.

A list of the documents referred to in this Standard is given in Appendix A.

5

STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND

Australian/New Zealand Standard

Plumbing and drainage

Part 0: Glossary of terms

6