铝结构 第2部分：许用应力设计

CONTENTS

6

2

AS/NZS 1664.2:1997

This Joint Australian/New Zealand Standard was prepared by Joint Technical Committee BD/50, Aluminium Structures. It was approved on behalf of the Council of Standards Australia on 27 June 1997 and on behalf of the Council of Standards New Zealand on 11 July 1997. It was published on 5 September 1997.

The following interests are represented on Committee BD/50:

Aluminium Development Council

Association of Consulting Engineers, Australia

Australian Building Codes Board

Institution of Professional Engineers New Zealand

University of Sydney

Review of Standards. To keep abreast of progress in industry, Joint Australian/New Zealand Standards are subject to periodic review and are kept up to date by the issue of amendments or new editions as necessary. It is important therefore that Standards users ensure that they are in possession of the latest edition, and any amendments thereto.

Full details of all Joint Standards and related publications will be found in the Standards Australia and Standards New Zealand Catalogue of Publications; this information is supplemented each month by the magazines ‘The Australian Standard’ and ‘Standards New Zealand’, which subscribing members receive, and which give details of new publications, new editions and amendments, and of withdrawn Standards.

Suggestions for improvements to Joint Standards, addressed to the head office of either Standards Australia or Standards New Zealand, are welcomed. Notification of any inaccuracy or ambiguity found in a Joint Australian/New Zealand Standard should be made without delay in order that the matter may be investigated and appropriate action taken.

This Standard was issued in draft form for comment as DR 96165.

3

AS/NZS 1664.2:1997

Australian/New Zealand Standard^®

Aluminium structures

Part 2: Allowable stress design

Originated in Australia as part of AS 1664—1975.
Previous Australian edition AS 1664—1979.
Jointly revised and designated AS/NZS 1664.2:1997.

Incorporating:
Amdt 1—1999

PUBLISHED JOINTLY BY:

STANDARDS AUSTRALIA
1 The Crescent,
Homebush NSW 2140 Australia

STANDARDS NEW ZEALAND
Level 10, Radio New Zealand House,
155 The Terrace,
Wellington 6001 New Zealand

ISBN 0 7337 1284 3

4

PREFACE

This Joint Standard was prepared by the Joint Standards Australia/Standards New Zealand Committee BD/50, Aluminium Structures, to supersede, in part, AS 1664—1979, Rules for the use of aluminium in structures (known as SAA Aluminium Structures Code).

This Standard is technically equivalent to The Aluminium Design Manual: Specifications and guidelines for aluminium structures. Part 1A: Specifications for Aluminium structures allowable stress design issued by the U.S. Aluminium Association Inc.

The objective of this Standard is to provide designers of aluminium alloy load carrying members and elements with allowable stress design criteria for use in design applications.

Statements expressed in mandatory terms in notes to tables and figures are deemed to be requirements of this Standard.

© Copyright — STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND

Users of Standards are reminded that copyright subsists in all Standards Australia and Standards New Zealand publications and software. Except where the Copyright Act allows and except where provided for below no publications or software produced by Standards Australia or Standards New Zealand may be reproduced, stored in a retrieval system in any form or transmitted by any means without prior permission in writing from Standards Australia or Standards New Zealand. Permission may be conditional on an appropriate royalty payment. Australian requests for permission and information on commercial software royalties should be directed to the head office of Standards Australia. New Zealand requests should be directed to Standards New Zealand.

Up to 10 percent of the technical content pages of a Standard may be copied for use exclusively in-house by purchasers of the Standard without payment of a royalty or advice to Standards Australia or Standards New Zealand.

Inclusion of copyright material in computer software programs is also permitted without royalty payment provided such programs are used exclusively in-house by the creators of the programs.

Care should be taken to ensure that material used is from the current edition of the Standard and that it is updated whenever the Standard is amended or revised. The number and date of the Standard should therefore be clearly identified.

The use of material in print form or in computer software programs to be used commercially, with or without payment, or in commercial contracts is subject to the payment of a royalty. This policy may be varied by Standards Australia or Standards New Zealand at any time.

5

CONTENTS

6