JB/T 8821-1998 WGJ type intermediate shaft drum gear coupling type, parameters and dimensions

JB/T 8821-1998 JB/T 8821-1998 WGJ type intermediate shaft drum gear coupling type, parameters and dimensions JB/T8821-1998 standard download decompression password: www.bzxz.net

[CS 21.120. 20
Machinery Industry Standard of the People's Republic of China
JB/T8821—1998
WGJ Crowned teeth couplings with interconntcting shaft-Typeparameters and size1998-9-30 Issued
National Machinery Industry Bureau
1998-12-01 Implementation
B 8821-1998
Appendix A of this standard is the appendix of the standard.
This standard is proposed and managed by the National Technical Committee for Standardization of Machine Shafts and Accessories. The responsible drafting unit of this standard is China Second Heavy Machinery Group Co., Ltd. Xi'an Heavy Machinery Research Institute. The main drafters of this standard are Lv Wanluo, Yue Baozi, Yue Guangfa, Zhang Ziming, and Zhang Guangye. This standard is published for the first time:
1 Scope
Machinery Industry Standard of the People's Republic of China
WGJ Crowned teeth cnuplinga witliatarcamnctlnt shaft-Type,parameiere and dimensions
wGJ Crowned teeth cnuplinga witliatarcamnctlnt shaft-Type,parameiere and slzeJI/T8821199
Jie standard defines the type, basic parameters and dimensions of type 1 intermediate disc gear coupling (hereinafter referred to as coupling). This standard is applicable to transmission systems that connect two non-directional shafts. The rotation diameter of the coupling end is 130~-1000mm. The nominal torque transmitted is G.3~3150kN·m. The angular offset when working load is 3”. When there is no working load, the directional offset is 5 pieces. WGJ type intermediate disc gear coupling.
2 Referenced standards
The texts contained in the following standards are included in the provisions of this standard by reference: This standard is reprinted, and the versions shown are valid. The standard may be revised. The parties using the technical standard should consider the possibility of using the new version of the listed standard. GB/T3852-1597
G 6403.4—85
IB/T613692
JB/T7511-1554
Shaft hole and chain type and size of coupling
Parts chamfer and chamfer
Interference fit sleeve press assembly and disassembly
Mechanical coupling reverse calculation
3 Type, basic number and main dimensions
31 The coupling type is divided into AB and center. A and B are the connection types that can almost part of the axial force on the basis of the center type or internal gear joint separation type 3. 2 Basic parameters and main dimensions
Type A shall comply with the provisions of Figure 1 and Table 1; Type B shall comply with the provisions of Figure 2 and Table 1; Type C shall comply with the provisions of Figure 3 and Table 1 and shall be applicable to WG,17~WGJ23.
3.3 Marking rules and marking methods
3.3.1 Marking method
Two-shaft end coupling
Type code A, RC (Type A is not marked)
Specification sequence code
Connecting shaft magnetic gear coupling
3.3.2 Marking rules
3.3.2..6 The marking of the chain coupling shall comply with the provisions of GB/T3852. Approved by Guodong Machinery Industry on September 30, 1998 and implemented on December 1, 1998. IB/T8821-1998 3.3.2.2 The marking rule for the coupling with no braid connection for hydraulic assembly and disassembly with interference fit is to mark Ur before the diameter of the shaft hole according to the provisions of JB3/T6186. 3.2.3 The marking rule for the flat hole shaft is to add \EK before the diameter of the shaft hole, that is, BKd, × B × L 3.3.3 Marking example Example W4A type coupling, the distance between the two shaft ends is -1m. Active type shaft hole, A type, = 120mm, L = 167mm. Driven type shaft hole, d, = 120 mm, t, = 167mm, B = 55mmWGJ4 coupling
J, 120 × 167
X1000JB/T8821-1008
BK120XS5X167
Regulation 2/GJ10B coupling, two shaft ends, electricity supplier L; = 1500mm active end: J shaft support B type key increase 4 = 24Cmm = 330mm hot end like hole d = 240mm.B = 180mmL = 330mmWGJI Ming coupling
dirty unclogging
BK240X180X330×1500 JE/TBB21-198J.B240X330
For the selection of fast axis static, please refer to Appendix A (standard attachment) 2
JB,T8821—1998
JB/T8821bZxz.net
JI/T8921--1998
JD/T $821 -1998
sztuet
GTTCOT
55·36
JD/T 2E1
Yingguangfei
Mianye
6D205T
IB/T 8B21-[998
G9E*cfe
JB/T Issue month 21
month*
oncnak
09*0r1
089098
c29 : 2r9
laizip
009095
299365
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.