GB 10205-2001 Monoammonium phosphate, diammonium phosphate

This standard specifies the product classification, requirements, test methods, inspection rules, labeling, packaging, transportation and storage of solid monoammonium phosphate (MAP) and diammonium phosphate (DAP) fertilizers. This standard applies to solid monoammonium phosphate and diammonium phosphate fertilizers produced by various processes. GB 10205-2001 Monoammonium phosphate, diammonium phosphate GB10205-2001 Standard download and decompression password: www.bzxz.net

GB102052001
Preface
Article 8.1 in Chapter 4, Chapter 7 and Chapter 8 of this standard are mandatory provisions, and the rest are recommended provisions. This standard is for (GI310205-1988 "Ammonium phosphate, diammonium phosphate (granular)", GB10206-1988 "Ammonium phosphate by slurry method", HG/T32821990 "Powdered monoammonium phosphate" HG25581994 "Slurry" The revision of "Method of Diammonium Phosphate" merges the four standards mentioned in 1: into one item.
The main differences between this edition and the previous edition are:
1 The scope of application of the standard has been changed to "solid monoammonium phosphate and diammonium phosphate fertilizers suitable for production by various processes". 2 Product classification has been added .
3 Based on the actual situation of my country's phosphate rock resources, the existing production conditions of ammonium phosphate and diammonium phosphate, and the physical quality of water, the requirements for ammonium phosphate and ammonium phosphate... were adjusted, and the matching formula was added. As an indicator, the water-soluble phosphorus indicator is changed to the water-soluble phosphorus percentage of available phosphorus indicator.
This standard will replace GB10205-1988, GB10206--1988, HG/T3282-1990 and HG2558---1994
This standard is proposed by the State Administration of Petroleum and Chemical Industry. This standard is under the jurisdiction and interpretation of the National Fertilizer and Soil Conditioner Standardization Technical Committee. The drafting unit of this standard is: National Fertilizer Quality Supervision and Inspection Center ( Shanghai), Sichuan Shihua Co., Ltd. The main drafters of this standard: Yang - Yi, Huang Daxiong, Yang Xiaoxia, Jing Wenzhong, Shang Zhaocong. This standard was first published in 1988
343||tt| |1 Scope
National Standard of the People's Republic of China
Monoanmmoniun phosphate and diammonium phosphateGB 10205--2001
Replace GB10205||tt| |GB 10206.
This standard specifies the product classification, requirements, test methods, and inspection of solid monoammonium phosphate (MAP) and diammonium phosphate (DAP) fertilizers Rules, labeling, packaging, transportation and storage. This standard applies to solid monoammonium phosphate and diammonium phosphate fertilizers produced by various processes. 2 Reference standards
The provisions contained in the following standards are adopted in this standard. The references constitute the provisions of this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the following new versions of the standard GB/T1250-1989. Numerical expression and judgment methods GB/T6679-1986 General principles for sampling of solid chemical products GB8569--1997 Solid chemical fertilizer packaging GB/T10209.1-2001 Determination of total nitrogen content in ammonium phosphate and diammonium phosphate (post-distillation titration method) GB/T10209.2-2001 Determination of available phosphorus content in ammonium phosphate and diammonium phosphate GB/T10209.3--2001 Determination of moisture content in ammonium phosphate and diammonium phosphate GB/T10209.4--2001 Ammonium phosphate, Determination of diammonium phosphate particle size GB18382-2001 Fertilizer labeling content and requirements (neqISO7409:1984) 3 product classification | Ammonium and diammonium phosphate: granular ammonium phosphate and diammonium phosphate obtained by using phosphoric acid concentration method, neutralizing phosphoric acid with ammonia or using other methods other than slurry concentration method. 3.2 Granular monoammonium phosphate and diammonium phosphate by slurry method: granular monoammonium phosphate and diammonium phosphate obtained by neutralizing phosphoric acid with ammonia using the slurry concentration method
3.3 Powdered monoammonium phosphate: without Granulated monoammonium phosphate is divided into two categories: those made from high-quality phosphate rock as raw materials and made by phosphoric acid concentration method are Category 1 products, and those made from medium and low-grade phosphate rocks with high magnesium, iron and aluminum content are used as raw materials. The product obtained by slurry concentration method is a genuine product. 4 Requirements
4.1 Traditional granular monoammonium phosphate and diammonium phosphate should meet the requirements of Table 1: Appearance: granular, no mechanical impurities.
Approved by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China on 2001-07~26 344
Implemented on 2002-01-01
Total nutrients (N+PO)
Total nitrogen (N)
Available phosphorus (calculated as P0,)
The percentage of water-soluble phosphorus in available phosphorus ≥
Particle size (1.00~4.00 mm)
Table 1
GB 10205—2001
Traditional granular monoammonium phosphate and diammonium phosphate Requirements for ammonium phosphate
Premium product
12-52-0
11-49-0
48.0|| tt||85
Qualified product
10-46-0
45.0 | | tt | | 2.5 | | tt | No mechanical impurities.
Table 2
Total nutrients (N+PO)
Total nitrogen (N)
Available phosphorus (calculated as P():)
Percentage of water-soluble phosphorus in available phosphorus
Moisture (H2O)
Particle size (1.00~4.00mm)
Superior product
18-46-0
Slurry method granular monoammonium phosphate and phosphoric acid Requirements for diammonium slurry method Monoammonium phosphate
Excellent product
11-47-0
4.3 Powdered ammonium phosphate should meet the requirements of Table 3: Appearance: powdery, no obvious agglomeration, no mechanical impurities. First Class
11-44-0
80| |tt||Qualifier
10-2-0
2.5||tt| |80
Table 3
Requirements for powdered monoammonium phosphate
Class 1
Total nutrients (N+PO)||tt| |Total wear (N)
Available phosphorus (based on PO.)
Percentage of water-soluble phosphorus in available phosphorus
Acceptance (H2O)
5 test methods| |tt||5.1 Determination of total nitrogen content
shall be carried out in accordance with GB/T10209.1.
Premium product
9-49-0
4.0||tt ||Equal products
8-47-0
5.2 Determination of available phosphorus content and water-soluble phosphorus as a percentage of available phosphorus Excellent product
11~47-0
80| |tt||3.0
diammonium phosphate
15-42-0
41.0|| tt||85
Qualified product
13-38-0
diammonium phosphate by slurry method
first-class product
15-42-0
57.0|| tt||14.0
Class 1
Other products
11-44 -0
Qualified product
13-38-0| |tt||51.0
Qualified product
10-42-0
345||tt| |According to GB/T10209.2.
5.3 Determination of moisture
shall be carried out according to G13/T10209.3,
5.4 Determination of particle size
shall be carried out according to GB/T10209.4. | |tt | The quality supervision department of the electrical production enterprise shall conduct inspections. The manufacturer shall ensure that all products shipped from the factory shall comply with the requirements of this standard. Each batch of products shall be accompanied by a quality certificate, which shall include: name, address, and product name of the manufacturer. , product category, product grade, batch number or production date, product net content, total nutrient content, formula and this standard number. 6.3 The user unit has the right to inspect the received products according to the inspection rules and inspection methods stipulated in this standard and check whether their quality indicators conform to the requirements of this standard.
6.4 If one index in the test results does not meet the requirements of this standard, samples should be taken from twice the amount of packaging bags for inspection and the results should be re-tested. Even if one index does not meet the requirements of this standard, The entire batch of products will not be accepted. 6.5 Products are inspected in batches, with the output of one or two days as a batch, and the maximum batch size is 5001. 6.6 For bagged products, when it does not exceed 512 bags, the number of sampling bags shall be determined according to Table 4; when it exceeds 512 bags, the number of sampling bags shall be determined according to the formula (1 ) The calculation result determines the number of sampling bags. If there is a decimal, round it up to an integer.
Table 4 Determination of the number of sampling bags
Total number of bags
1～10
65 ~ 81 | | tt |
Minimum number of sampling bags
All bags
15||tt ||16
Total number of bags
182216
217254
255~296
297343
314~ 394
395~450
451~512
Number of sampling bags=3× N
Minimum number of sampling bags
According to table 4 or formula (1 ) calculation results, randomly select a certain number of bags, insert a sampler from the longest diagonal line of each bag to 3/4 of the bag, and take out no less than 100g of samples. The total sample volume taken in each batch must not be less than 2kg. Sampling of packaged products shall be carried out in accordance with the provisions of GB/T6679. 6.8 Sample reduction: Mix the collected samples quickly, use a divider or the quartering method to reduce the sample to about 1000g, and divide it into two clean and dry bags. 500mi sealed in a wide-mouth bottle or polyethylene bottle with a ground stopper, affixed with a label, indicating the name of the manufacturer, product name, batch number, sampling month, name of the sampler, one bottle for product quality analysis, one bottle for storage Months for future reference. 6.9 Sample preparation: Divide a bottle of 500g sample from 6.8 several times and take out about 100g sample. Quickly grind all the samples to pass the 0.50mnl aperture test sieve (if the sample is wet or It is difficult to crush, but it can be ground until all the materials pass through the 1.00mm aperture test sieve), mixed evenly, and placed in a clean, dry bottle for composition analysis. 6.10 Any objections between the supplier and the buyer regarding product quality require arbitration. , should be carried out in accordance with the relevant provisions of the "Product Quality Arbitration Inspection and Product Quality Appraisal Management Measures"
7 Marking
GB 10205
5-2001||tt. ||The product category (such as traditional method, slurry method, Category 1, Category II, etc.) should be indicated in the form of a combination formula. Total nitrogen and effective phosphorus pentoxide content (such as diammonium phosphate NP()-K0: 18-46-0). The rest shall be marked according to the regulations of GB18382. Packaging, transportation and storage
8.1 The product shall be lined with polyethylene film bag or polypropylene woven bag with inner coating. Packaging should be carried out in accordance with the regulations of GB8569. The net content of each bag is (50±0.5)kg, (40±0.4)kg, (25±0.25)kg, and the average net content of each batch of products shall not be less than 50.0kg, 40. kg.25.0 kg.
2 Products can be transported in bulk or packaged. Products should be protected from rain, moisture, sun and cracking during storage and transportation. 8.2
If there is a decimal, it is rounded up to an integer.
Table 4 Determination of the number of sampling bags
Total number of bags
1～10
65 ~ 81 | | tt |
Minimum number of sampling bags
All bags
15||tt ||16
Total number of bags
182216
217254
255~296
297343
314~ 394
395~450
451~512
Number of sampling bags=3× N
Minimum number of sampling bags
According to table 4 or formula (1 ) calculation results, randomly select a certain number of bags, insert a sampler from the longest diagonal line of each bag to 3/4 of the bag, and take out no less than 100g of samples. The total sample volume taken in each batch must not be less than 2kg. Sampling of packaged products shall be carried out in accordance with the provisions of GB/T6679. 6.8 Sample reduction: Mix the collected samples quickly, use a divider or the quartering method to reduce the sample to about 1000g, and divide it into two clean and dry bags. 500mi sealed in a wide-mouth bottle or polyethylene bottle with a ground stopper, affixed with a label, indicating the name of the manufacturer, product name, batch number, sampling month, name of the sampler, one bottle for product quality analysis, one bottle for storage Months for future reference. 6.9 Sample preparation: Divide a bottle of 500g sample from 6.8 several times and take out about 100g sample. Quickly grind all the samples to pass the 0.50mnl aperture test sieve (if the sample is wet or It is difficult to crush, but it can be ground until all the materials pass through the 1.00mm aperture test sieve), mixed evenly, and placed in a clean, dry bottle for composition analysis. 6.10 Any objections between the supplier and the buyer regarding product quality require arbitration. , should be carried out in accordance with the relevant provisions of the "Product Quality Arbitration Inspection and Product Quality Appraisal Management Measures"
7 Marking
GB 10205
5-2001||tt. ||The product category (such as traditional method, slurry method, Category 1, Category II, etc.) should be indicated in the form of a combination formula. The content of total nitrogen and effective phosphorus pentoxide (such as diammonium phosphate NP()-K0: 18-46-0). The rest shall be marked according to the regulations of GB18382. Packaging, transportation and storage
8.1 The product shall be lined with polyethylene film bag or polypropylene woven bag with inner coating. Packaging should be carried out in accordance with the regulations of GB8569. The net content of each bag is (50±0.5)kg, (40±0.4)kg, (25±0.25)kg, and the average net content of each batch of products shall not be less than 50.0kg, 40. kg.25.0 kg.
2 Products can be transported in bulk or packaged. Products should be protected from rain, moisture, sun and cracking during storage and transportation. 8.2
If there is a decimal, it is rounded up to an integer.
Table 4 Determination of the number of sampling bags
Total number of bags
1～10
65 ~ 81 | | tt |
Minimum number of sampling bags
All bags
15||tt ||16
Total number of bags
182216
217254
255~296
297343
314~ 394
395~450
451~512
Number of sampling bags=3× N
Minimum number of sampling bags
According to table 4 or formula (1 ) calculation results, randomly select a certain number of bags, insert a sampler from the longest diagonal line of each bag to 3/4 of the bag, and take out no less than 100g of samples. The total sample volume taken in each batch must not be less than 2kg. Sampling of packaged products shall be carried out in accordance with the provisions of GB/T6679. 6.8 Sample reduction: Mix the collected samples quickly, use a divider or the quartering method to reduce the sample to about 1000g, and divide it into two clean and dry bags. 500mi sealed in a wide-mouth bottle or polyethylene bottle with a ground stopper, affixed with a label, indicating the name of the manufacturer, product name, batch number, sampling month, name of the sampler, one bottle for product quality analysis, one bottle for storage Months for future reference. 6.9 Sample preparation: Divide a bottle of 500g sample from 6.8 several times and take out about 100g sample. Quickly grind all the samples to pass the 0.50mnl aperture test sieve (if the sample is wet or It is difficult to crush, but it can be ground until all the materials pass through the 1.00mm aperture test sieve), mixed evenly, and placed in a clean, dry bottle for composition analysis. 6.10 Any objections between the supplier and the buyer regarding product quality require arbitration. , should be carried out in accordance with the relevant provisions of the "Product Quality Arbitration Inspection and Product Quality Appraisal Management Measures"
7 Marking
GB 10205
5-2001||tt. ||The product category (such as traditional method, slurry method, Category 1, Category II, etc.) should be indicated in the form of a combination formula. Total nitrogen and effective phosphorus pentoxide content (such as diammonium phosphate NP()-K0: 18-46-0). The rest shall be marked according to the regulations of GB18382. Packaging, transportation and purchase and storage
8.1 Woven bags lined with polyethylene film or polypropylene woven bags with inner coating. Packaging should be carried out in accordance with the regulations of GB8569. The net content of each bag is (50±0.5)kg, (40±0.4)kg, (25±0.25)kg, and the average net content of each batch of products shall not be less than 50.0kg, 40. kg.25.0 kg.bzxZ.net
2 Products can be transported in bulk or packaged form. Products should be protected from rain, moisture, sun and cracking during storage and transportation. 8.2
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.