GB/T 4604-1993 Radial clearance of rolling bearings

This standard specifies the radial clearance values ​​of the following types of cylindrical bore bearings and tapered bore bearings. A. Deep groove ball bearings (except for outer spherical ball bearings, whose clearance values ​​are specified in JB 5304); b. Self-aligning ball bearings; c. Cylindrical roller bearings; d. Needle roller bearings; e. Spherical roller bearings. The radial clearance values ​​of double-row cylindrical roller bearings are recommended in the appendix. The clearance values ​​given are applicable to bearings without preload and bearings that can withstand pure radial loads in their structure. The clearance values ​​listed in this standard are for subscribers to use when inspecting bearings. GB/T 4604-1993 Radial clearance of rolling bearings GB/T4604-1993 Standard download decompression password: www.bzxz.net

[rDC 621. 822. 6
National Standard of the People's Republic of China
GB/T4604—93
Rolling bearingsRadial internal clearance1993-03-01Promulgated
Implementation on 1993-12-01
Promulgated by State Technical Supervision Bureau
National Standard of the People's Republic of China
Rolling bearings-Radial internal clearanceThe standard is equivalent to the international standard set [S0575] 191 Bearing radial clearance group standard
Subject content and scope of application
This standard stipulates the radial clearance of the following types of wide-hole thrust bearings and national standard bearings. The groove ball bearing (except for the outer ball bearing, the clearance value is specified in B5301: a. Self-aligning block bearing; Net column bearing: Needle bearing: Self-aligning lacquer bearing. The longitudinal clearance value of double-row net column roller is introduced in the appendix. The clearance value given in GB/T460493 is applicable to bearings without folding load and bearings that can bear pure radial negative load in structure. The clearance values ​​listed in this standard are for the subscriber to inspect the shaft. 2 Reference standards GB4D9 Definition of dynamic bearing tolerances GB SAC1
Bearing series dimensions and tolerances for grooved ball bearings
B3C4Drawing bearingsExternal spherical bearingsRadial play3 Jianwen
The definition of radial play of bearings (without bearing load and capable of bearing pure radial load) is now defined in 6.1.1 of GH4199. 4 Light radial play value
4.1 The radial play of grooved ball bearings shall comply with the provisions of Table 1. National Technical Supervision Product 1993-03-01Approved 1993-12 01 Implementation
Nominal inner diameter
GB4604-93
Table 2 Deep-hole self-aligning ball bearings
4.2 The radial play of self-aligning ball bearings shall comply with the provisions of Table 2 and 3.2 Nominal inner diameter
GB/T4604-93
Table 2 Circular hole self-aligning bearings
Table 2 Taper hole self-aligning ball bearings
4.3 The radial play of cylindrical bearings shall comply with the provisions of Table 4.3 Rough
Ttuici
4 Dimensional clearance of roller bearings
CD/T46D4
4 Cylindrical bore cylindrical roller bearings
Except for the needle roller bearings and heavy series needle roller bearings with internal and external retainers, the radial clearance values ​​of the four-column roller bearings specified in Table 4 are adopted for the needle roller bearings with internal and external retainers (see GB1603) and the internal retainer bearings as separate parts. The radial clearance is determined by the inner diameter of the needle roller assembly: the diameter is specified in GB1603 and GB8. 4.5 The radial clearance of the bearings with radial limit should meet the requirements of Table 5 and Table 6. 4
Nominal inner diameter
CB/T4604-93
Table 5 Cross-hole self-aligning bearings
Nominal inner diameter
GB/T4604-93
Number of inner diameters
CB/T 4604-93
Appendix A
Radial diameter of double-row cylindrical roller bearings (supplements)bzxZ.net
Table A1 Radial diameter of tapered-hole cylindrical roller bearings
Table A2 Radial diameter of cylindrical roller bearings with tapered holes
Nominal inner diameter
Additional instructions:
GB/T 4604—93
Continued Table A2
This standard was proposed by the Ministry of Machinery and Electronics Industry of the People's Republic of China.
This standard was developed by the Ministry of Machinery and Electronics Industry. This standard was first issued in 1984.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.