JB/T 9897-1999 Accuracy test of universal radial drilling machine without base

JB/T 9897-1999 This standard is a revision of JB 4242.1-86 "Accuracy of Universal Radial Drilling Machines without Bases". During the revision, only editorial changes were made according to relevant regulations, and the technical content was not changed. The standards matching this standard are: GB/T 2815-1989 Drilling Machine Spindle End JB/T 6335.1-1999 Radial Drilling Machine Series JB/T 6336-1992 Technical Conditions for Universal Radial Drilling Machines This standard specifies the requirements and inspection methods for the geometric accuracy inspection and working accuracy inspection of universal radial drilling machines without bases. This standard is applicable to universal radial drilling machines without bases with a maximum drilling diameter of 25~80mm. This standard was first issued in July 1986. JB/T 9897-1999 Accuracy test of universal radial drilling machine without base JB/T9897-1999 standard download decompression password: www.bzxz.net

1CS25.080.40
Machinery Industry Standard of the People's Republic of China
JBT9897—1999
Universal Radial Drilling Machine without Base
Precision Inspection
Published on 1999-15-2
National Bureau of Machinery Industry
Implementation on 2000-01-01
JH/T9897—1999
This standard is the precision specification of universal radial drilling machine without base B42421.4. It has only been edited and revised according to relevant regulations, and the technical content has not changed. The standards supporting this standard are:
GB/T2815—19R9
JB/T6335.1—1999
JB/T6336—1992
Drilling end
Drilling beam series spectrum
Power push drilling water conditions
The Appendix A of this standard is the appendix of the standard.
This standard replaces B4242.1-8 from the date of implementation. This standard is proposed by the National Metal Cutting Machine Tool Standardization Technical Committee. This standard is under the jurisdiction of the Drilling Machine Branch of the National Metal Cutting Machine Tool Standardization Technical Committee. The drafting units of this standard are: Zhongjie You" and Tianjin Fourth Machine Tool Factory. This standard was first issued in July 198%.
1 Scope
Machinery Industry Standard of the People's Republic of China
Baseless Universal Radial Drilling Machinebzxz.net
Precision Inspection
JB/T9897—1999
4 This standard specifies the requirements for precision control inspection and working precision inspection of baseless universal radial drilling machines. This standard is not applicable to baseless universal radial drilling machines with a maximum drilling diameter of 25mm. 2 Referenced Standards
The provisions of the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised quickly. All parties using this standard should consider the possibility of using the latest version of the following standards: (H/17421.1-1 State 8 Peach Machine Tool Test General Rules Part 3: Geometrical Accuracy of Machine Tools under No-load or Loading 3 General Requirements
3.1 When using this standard, the relevant provisions of CBT17421.1 should be followed. In particular, the installation of the spindle and other components before testing, the temperature rise during operation, the inspection method and the accuracy of the inspection tools. 3.2 The order of the accuracy inspection items listed in this standard does not indicate the actual order. In order to install and disassemble the inspection tools and the inspection force, any order can be used. 3.3 When the actual measured length is different from the length specified in the standard, the tolerance shall be converted according to the length that can be measured according to the provisions of 2.3.1.1 of B17421.1-18. When the conversion result is less than 0.001nmn, it shall still be calculated as 0.00m. 3.4 The longitudinal plane referred to in this standard is the vertical plane passing through the main axis (when the main axis is in a vertical state) and the vertical axis: the plane between the can and the vertical plane (when the test is in a vertical state) is the plane between the can and the vertical plane. 3.5 If there are special provisions in the "Test Method" column of Section 5 of this standard, the main axis should be in a zero position and tightened. 3.6 According to the agreement between the user and the manufacturer, the inspection items can be increased: Approved by the National Machinery Industry Bureau on May 20, 1999, implemented on January 1, 2000, JB/T98971999, 0001010, 3B/T9897-1999, 0001010, 3B/T9897-1999, 0001010, 3B/T9897-1999, 0001010, 3B/T9897-1999, 0001010, 3B/T9897-1999, 0001010, 3B/T9897-1999, 0001010, 3B/T9897-1999 9897-1999
Kai some round
Fixed foot please building
Firewood rack
1 Storage tools
JB/T9897-1999
JBT0897—1999
Appendix A
[Standard record]
Corresponding relationship between output value and hole diameter
4 The corresponding relationship between the density F of the positive base force and the pin hole diameter is shown in Table A], Table A1
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.