JB/T 9166-1998 Process Document Numbering Method

JB/T 9166-1998 JB/T 9166-1998 Process Document Numbering Method JB/T9166-1998 Standard Download Decompression Password: www.bzxz.net

ICS25.010
Standard of the Machinery Industry of the People's Republic of China
JB/T9166-1998
Numbering method for technological documentation1998-11-16 Issued
National Bureau of Machinery Industry
1998-12-01 Implementation
JB/T9166-1998
This standard is a revision of JB/Z254-85 "Numbering method for technological documentation". Only editorial changes were made during the revision, and the main technical content remained unchanged.
This standard replaces JB/Z254-85 from the date of implementation. Appendix A of this standard is a prompt appendix.
This standard was proposed and managed by the Mechanical Science Research Institute. The main responsible drafting unit of this standard is the Mechanical Science Research Institute. The main drafters of this standard are Ma Xianzhi, Li Qin, Hu Huiqing, and Shi Junwei. 1
1Scope
Standard of the Machinery Industry of the People's Republic of China
Numbering method for technical documentation
Numbering method for technical documentation This standard applies to the numbering of various types of process documents commonly used by various machinery manufacturing enterprises. 2Referenced standards
JB/T9166-1998
Replaces JB/Z25485
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and the parties using this standard should explore the possibility of using the latest versions of the following standards. JB/T9165.2—1998 Process specification format JB/T9165.3—1998 Management process document format 3General
3.1All formal process documents must have independent numbers. The same number can only be assigned to one process document. Note: A process document refers to the smallest unit process document that can be used alone, such as the casting process card, machining process card, and machining process card of a certain part, which are all the smallest unit process documents that can be used alone. 3.2 When the same document consists of several pages, each page should be filled with the same number. 3.3 When citing and borrowing a process document, its number should be indicated. 3.4 The number of the process document should be filled in according to the position specified in JB/T9165.2 and JB/T9165.3. 4 Composition of the number
4.1 The composition of the process document number is recommended in the following two forms, and each enterprise can choose one according to its own situation. 4.1.1 It consists of two parts: the process document feature number and the registration sequence number, and the two parts are separated by a line. X××x
Registration sequence number
Process document feature number
4.1.2 It consists of the product code (model) plus the process document feature number plus the registration sequence number, and the parts are separated by a line. X××XX
Registration sequence number
Process document feature number
Product code (model)
, the process document feature number includes two parts: process document type code and process method code, each part consists of two digits. 4.2
Approved by the State Machinery Industry Bureau on November 16, 1998 and implemented on December 1, 1998
JB/T9166-1998
Process method code
Process document type code
Registration sequence number generally starts from 1 and increases continuously in each document feature number, and the number of digits is determined according to needs. 4.3
5 Code compilation rules and registration method
5.1 The process document type code is specified in Table 1. The process method code is specified in Table 2.
5.3 The registration sequence number is uniformly given by the process standard department of each enterprise. 5.4 The process documents need to be registered when they are numbered. The registration form is recommended to be in Appendix A (the appendix of the suggestion). Process documents with different characteristic numbers cannot be registered in the same registration form. 5.5
Process documents that have been re-painted after multiple modifications should have A, B, C, etc. added after their original numbers to distinguish them. 5.6
Examples of process document numbers
a) Numbers without product codes (models): Process plan: 0200-5
Sand casting process card: 2211-15
Machining process key parts list: 3140112 Forging material consumption process quota list: 51219700 Machining special process equipment list: 61408201b) Numbers with product codes (models): C6120 Horizontal lathe process plan: C61200200-5XA6132 Universal milling machine process route table: XA61321000202V-6/8 air compressor machining process card: 2V-6/8-2340-1352XZ8 Direct-coupled rotary vane vacuum pump process summary: 2XZ-897008526 Note: The registration sequence numbers in the examples are all assumed. Table 1 Process document type code
Process document type code
Process document type name
Process document directory
Process plan
Process route table
Process document type code
Process document type name
Workshop division of labor details table
Process document type code
JB/T9166-1998
Table 1 (end)
Process document type name
Process specification
Process card
Process card
Process card
Calculation-adjustment card
Inspection card
Process rulesbZxz.net
Process quality management document
Process quality analysis table
Operation instruction card (work instruction)
Control chart
() Parts list
Process key parts list
Outsourced parts list
Outsourced parts list
Matching parts list Detailed table
Detailed table of accessories
Consumption quota table
Process document type code
Process document type name
Detailed table of material consumption process quota
Summary table of material consumption process quota
Detailed table of process equipment
Detailed table of special process equipment
Detailed table of purchased tools
Detailed table of factory standard (general) tools
Detailed table of combined fixtures
Detailed table of workstation equipment
(to be Development)
(To be developed)
Process equipment design task book
Special process equipment instruction manual
Process equipment verification book
Process test report
Process summary
Process method code
Process method name
Not specified
Sand casting
Pressure casting
Investment casting
Metal mold casting
Wood mold manufacturing
Sand and mud core manufacturing||tt ||Hot stamping
Cold stamping
Spinning
Powder metallurgy
Plastic parts injection
Plastic parts pressing
Arc welding and electroslag welding
Resistance welding
JB/T9166-1998
Process method code
Process method code
Process method name
Friction welding
Gas welding and gas cutting
Machining
Single-axis automatic lathe processing| |tt||Multi-axis automatic lathe machining
Gear machine machining
Automatic line machining
CNC machine machining
Optical machining
Typical machining
Group machining
Electrical machining
Electrical discharge machining
Electrolytic machining
Wire cutting
Laser machining
Ultrasonic machining
Electron beam machining
Ion beam machining
Heat treatment
Induction heat treatment
High frequency heat treatment
Chemical heat treatment
Process method code
Process method name
Tool heat treatment
Surface treatment
Metal spraying
Shot peening
(To be developed)
Cold working, assembly, packaging
Electrical installation
A1Format of the registration form for process document number
Sequence number
A2Filling in the contents of each column of the registration form
(1) Number Process file name:
(2) Characteristic number of the file;
JB/T9166-1998
Appendix A
(Suggested Appendix)
Process file number registration
Applicant for number
(3) Registration order of files with this characteristic number:(4) Unit code or name of the applicant for number:(5) Name of the applicant for number:
(6) Registration date;
(7) Product code (model) using this number file. The size of each column in the A3 table is not limited and can be determined by each enterprise when using it. Issue
Feature number
Products used
People's Republic of China
Mechanical Industry Standard
Process document numbering method
JB/T9166-1998
Published and issued by the Mechanical Science Research Institute
Printed by the Mechanical Science Research Institute
(No. 2 Shouti South Road, Beijing
Format 880×1230
First edition in December 1998
Print run 1-500
100044)
Printing head
Word count 12,000
First printing in December 1998
Price 10.00 yuan
98-199
Mechanical Industry Standard Service Network:
861_9916
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.