
JB/T 10118-1999 Heart-shaped chucks for machine tool fixture parts and components
time:
2024-08-12 02:16:49
- JB/T 10118-1999
- in force
Standard ID:
JB/T 10118-1999
Standard Name:
Heart-shaped chucks for machine tool fixture parts and components
Chinese Name:
机床夹具零件及部件 鸡心卡头
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
Original standard number GB/T 12883-1991
Focal point Organization:
Mechanical Science Research InstitutePublishing Department:
Mechanical Science Research Institute

Skip to download
Summary:
JB/T 10118-1999 This standard specifies the heart-shaped chucks for workpieces with a diameter of 3 to 130 mm. This standard was first issued in 1983 as JB 3392-83 and revised for the second time in 1991 as GB/T 12883-91. JB/T 10118-1999 Heart-shaped chucks for machine tool fixture parts and components JB/T10118-1999 Standard download decompression password: www.bzxz.net

Some standard content:
IC5 28.060.41
Mechanical Industry Standard of the People's Republic of China
The parts and units of jigs and fixtures1999-08-06PromulgatedbzxZ.net
State Machinery Industry Bureau
Implementation on 2000-01-01
1Model
Mechanical Industry Standard of the People's Republic of China
Machine tool parts and components
Peach slaped pawl
The parts and units nf jigy and fixturesPeach slaped pawl
This standard specifies the dimensions of the heart chuck 2 suitable for upper parts with a diameter of 3-13mm
The dimensions are shown in the following figure and table.
Guosuo Machinery Industry approved 306 on August 6, 1999
JB101-9
2000-01-01 implementation
Nominal diameter
(recent information 1 bucket diameter)
>6- 12
>12 - 18
>18 - 25
>25-35
>15 -50
>50 - 65
>100 -130
3 Marking
3.1 Marking example:
JB/T10118-1999
Nominal diameter 12.-18m type chicken heart head: clamp head A12-1RJET[0118—1909
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Mechanical Industry Standard of the People's Republic of China
The parts and units of jigs and fixtures1999-08-06PromulgatedbzxZ.net
State Machinery Industry Bureau
Implementation on 2000-01-01
1Model
Mechanical Industry Standard of the People's Republic of China
Machine tool parts and components
Peach slaped pawl
The parts and units nf jigy and fixturesPeach slaped pawl
This standard specifies the dimensions of the heart chuck 2 suitable for upper parts with a diameter of 3-13mm
The dimensions are shown in the following figure and table.
Guosuo Machinery Industry approved 306 on August 6, 1999
JB101-9
2000-01-01 implementation
Nominal diameter
(recent information 1 bucket diameter)
>6- 12
>12 - 18
>18 - 25
>25-35
>15 -50
>50 - 65
>100 -130
3 Marking
3.1 Marking example:
JB/T10118-1999
Nominal diameter 12.-18m type chicken heart head: clamp head A12-1RJET[0118—1909
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- JB/T 6225-1992 General technical requirements for inductive phase shifters
- GB/T 2900.58-2002 Electrical terminology Generation, transmission and distribution power system planning and management
- JB/T 2001.10-1999 Types and dimensions of circular flanges for water systems (PN=20MPa)
- GB/T 3857-1987 Test method for chemical resistance of glass fiber reinforced thermosetting plastics
- JB/T 6382.4-1992 Cone seal welding type cone thread 90. Elbow pipe joint
- GB/T 21578-2008 Dangerous goods - Koenen test method
- GB 5491-1985 Sampling and subsampling methods for inspection of grain and oilseeds
- SJ 1539-1987 Nickel and Nickel alloy bars for vacuum tubes
- JB/T 58651.2-1999 Fastener product quality classification bolts
- GB/T 2814-2003 Vertical drilling machine parameters
- JB/T 9532-1999 Technical requirements for MIG/MAG welding guns
- GB/T 8894-1988 Circular copper alloy waveguide
- GB/T 5177.3-1985 Determination of average relative molecular weight of industrial alkylbenzenes - Gas-liquid chromatography
- GB 16280-1996 Technical requirements and test methods for linear heat-sensing fire detectors
- JB/T 9936.1-1999 Parameters of flat jaw pliers for tilting machines
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail:bzxznet@163.com