JB/T 5275-1991 YW series and Y-WF series outdoor and outdoor chemical corrosion-resistant three-phase asynchronous motor technical conditions (frame size 80 ~ 315)

This standard specifies the types, basic parameters and dimensions, technical requirements, test methods and inspection rules, as well as marking and packaging requirements for outdoor and outdoor corrosion-resistant three-phase asynchronous motors. This standard applies to motors used outdoors and in outdoor corrosive environments. Motors are divided into outdoor light corrosion-resistant type (YW), outdoor medium-corrosion resistant type (Y-WF1) and outdoor based on the severity of the environmental chemical media they can withstand. Anti-strong corrosion type (Y-WF2). JB/T 5275-1991 YW series and Y-WF series outdoor and outdoor chemical corrosion-resistant three-phase asynchronous motor technical conditions (frame size 80 ~ 315) JB/T5275-1991 Standard download and decompression password: www.bzxz.net

Machinery Industry Standards of the People's Republic of China
YW and Y-WF series, outdoor and outdoor chemically resistant three-phase asynchronous motor technical conditions (frame size 80~315)
1Theme content and scope of application
JB5275--91
This standard specifies the type, basic parameters and gauges, technical requirements, test methods and inspections of outdoor and outdoor anti-corrosion three-phase asynchronous motors (hereinafter referred to as motors) rules and requirements such as marking and packaging. This standard is applicable to motors used outdoors and in outdoor corrosive environments. According to the severity of the chemical media that they can withstand, they are divided into outdoor anti-light corrosion type (YW), outdoor anti-moderate corrosion type (Y-WFI) and outdoor anti-light corrosion type (Y-WFI). Anti-strong corrosion type (Y-WF2) 2 cited standards
GB755 basic technical requirements for rotating motors
GB4942.1 motor shell protection level
GB1993 motor cooling method
GB997
Motor structure and installation type code
GB10068 Rotating electrical machine vibration measurement method and limit value Rotating electrical machine noise measurement method and limit value
GB 10069
GB1032||tt| |Test methods for three-phase asynchronous motors
GB 2423.1
Basic Environmental Testing Procedures for Electrical and Electronic Products Test A: Low Temperature Test Methods (GB 2423.4
Basic Environmental Testing Procedures for Electrical and Electronic Products Test Db: Alternating damp heat test method GB 191
Packaging, storage and transportation pictorial mark
GB 4772.1
ZB K04 001
Motor dimensions and tolerances
Environmental technical requirements for indoor and outdoor anti-corrosion electrical products for motors with frame sizes 36~400 and flange numbers FF55~FF1080 or FT55~FT108 J13833 Tropical motor technical conditions
JB2420 Painting of outdoor anti-corrosion electrical products JI3/ Z294 AC low-voltage motor loose-embedded winding insulation test method JB/Z346 AC low-voltage motor loose-embedded winding inter-turn insulation test limit 3 types, basic parameters and dimensions
3.1 The motor shell protection level should not be lower than IP54 (See GB4942.1). If you need to order a motor with a shell protection level higher than TP54, the user should consult with the manufacturer.
3.2 The cooling method of the motor is IC0141 (see GB1993). For IMB3, IMB5, IMB6, IMB7, IMB8, IMB35, IMV1, IMV3, IMV5, IMV6, IMV15 and IMV36 (see GB997), they are manufactured according to the provisions of Table 1. 3.4 The rating of the motor is based on the continuous working system (S1). Continuous rating. 3.5 The rated frequency of the motor is 50Hz and the rated voltage is 380V. The power is Y connection and the other power is Z connection.
Ministry of Mechanical and Electronic Industry of the People's Republic of China 1991-06. -28 approved 220
Implemented on 1992-07-01
Frame number
80~160
180-225
250~315||tt ||JB5275—91
Table 1
structure
structure
installation
generation|| tt||B3, B5, B6, 37, B8, 1335, V1, V3, V5, V6.V15, V36B3.B5.B35.V1
B33.B35.V1
3.6 motor should Manufactured according to the following rated power: No. (IM)
0.55,0.75,1.1,1.5,2.2,3,4,5.5.7.5,11,15,18.5,22,30,37.45,35,75,90.110 .132.160.200kw
The corresponding relationship between the motor’s frame number, speed and power should be as specified in Table 2. Table 2
Interstep
1||tt| |2
280M|| tt||315S
1.5|| tt||2. 2
18.5|| tt||22
110||tt| |132
1.1||tt| |1.5
15|| tt||18.5
90||tt| |110
revolution
speed,/min
1000||tt ||Rate,kw
7. 5| |tt||11
55||tt ||75
Note: The numbers 1 and 2 after S, M and 1 respectively represent the same frame number and different speeds. Power, 3.8
Motor dimensions and tolerances
4||tt| |5.5
The installation dimensions and tolerances of the motor should comply with the provisions of Table 3 to Table 6 : The overall dimensions should not be larger than those specified in Table 3 to 221
Frame number
225S| |tt||225M
Number of poles| |tt||2, 1
2, 4, 6
4, 6.8| |tt||4, 6.8
4.6.8, 10
4.6. 8.10
Basic sizeBasic size
190|| tt||216
508||tt| |4, 6, 8, 10
Basic size
100| |tt||100
254||tt ||241
H80-132
Table 3 base with feet and end cover|| tt | |tt||63
199||tt ||216
Note: 1) GE1)—G. The limit deviation of GE is 2 for frame size 80. The position tolerance of the K hole is based on the axis of the shaft extension. 222
, the rest are
60|| tt||65
80||tt| |65
.0..09
0.002||tt ||+0.030
1.1.|| tt||11
0.370| |tt||0.130)
0-500
527591
H160-315
No flange The motors
public
difference
Basic size limit deviation Basic size limit deviation Basic size limit deviation Basic size limit deviation Position tolerance 0
18|| tt||20
0||tt| |0.043
33||tt ||37
0| |tt||0.10
132|| tt||160
0||tt| |0.5
24||tt| |28
355| |tt||395
Outside
Shape||tt ||175
190| |tt||210
576||tt ||n
385||tt| |430
820|| tt||815
365| |tt||[31
机座号凸缘号
goss||tt ||90L
250M| |tt||280S
FF500||tt ||极
【北京
2、4、6
2、4.6.8
4、6、8
2|| tt||4.6.8
H80-132
A/2||tt| |基度
基度基度小小基度
编差北京
尺尺州
356| |tt||406
178||tt ||203
1、6、8、10
4||tt ||4.6、8、10
14063| |tt||14070
89||tt ||108
305133
349168
457216
±3.0||tt| |19
55||tt| |60
安| |tt
deviation
size|| tt||6
110±0.430
14| |tt||16
140±0. 50d 18
100.43016
±0.50018
18 170 S孔电影度公差以长伸的長线的基谁。 3）长在的最好最好值。
4)长的凸缘度面至长伸肩的长说。224
17160-315
装||tt| |机得
机座带底脚、端盖
基度：得京|| tt||心内家
0.03015.5
37| |tt||12.5
basic limit
尽计「自定
-0. 05267. 5-- 0. 20
-9-.043 58
o.052/67.5
0.052||tt ||71
[|| tt||71
5275---91
上凸缘的电视机
天天果生
尺||tt| | deviation
24||tt| |+0.520
位作度
H80-200
M basic
165130
265230
300250
limita
devija
350300±0.016400
400350±0.018450
500|450±0.020550
600 550|±0. 022660 |±3.0
H225～315
位作度
公|| tt||差
1.5| |tt||5
ultaza||tt| |可以
发店尺
ABACADH||tt| |165
1801195
15011751290
2051215
18012451380
215240190
280275:210
265:385
330||tt| |335:
355138028514
1395142013
435|47513451530 815
4901515|385|575|930
55015851410 640
1050||tt ||1240
744164515761865
机座号
132M||tt| |160M
凸缘号||tt ||FF165
极数||tt| |2、4
2、4、6
basic|| tt||size
55||tt| |60
H80--132 bZxz.net
||—0.004
40| |tt||50
E||tt || ??????
deviation
注：1)(GE=DG。GE的正解减容；机座号80警【2）”包装的以业正解值、
3）R的得缘可以面至达伸肩的这些。4）5孔可以度公差以达伸的达线的结果。224
6||tt ||8
， 这个载[
H160--225
机座不带底脚、端盖
-0.20| |tt||M
5275—91| |tt||H80-200
上有凸缘的电视机
130| |tt||180
limita
deviation
-0.011| |tt||+0.016
p2)||tt| |200
R3 1.5 |tt||±2.0
deviation
使用度
公||tt| |差「北京
275| |tt||210)
315|| tt||345
：245
515|| tt||605
845||tt| |227
机座号
250M||tt| |280S
得缘号
FF350||tt| |FF400
2、4、6、8
2||tt ||4.6.8
4、6、8
2| |tt||4.6、8、10
65| 4.6.8.1080 ||+0.018
140||tt ||+0.030
注：1） GE=D—G。GE的在在地场的了的（2）P在线的在线在地值。
±0.430||tt| |±0.500
3）R的得缘这些面至达伸肩的运动。4）S孔的使用度公差以间伸的间线的结果228
16||tt ||20
22.座不带底脚，端盖安
58| |tt|| limit
deviation
400|| tt||500
300||tt || limit
deviation
350 1. 0. 018
550±0.022
58| |tt|| limit
deviation
400|| tt||500
300||tt || limit
deviation
350 1. 0. 018
550±0.022
58| |tt|| limit
deviation
400|| tt||500
300||tt || limit
deviation
350 1. 0. 018
550±0.022
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.