JB/T 10120-1999 Machine tool fixture parts and component clamps
time:
2024-08-12 02:16:13
- JB/T 10120-1999
- in force
Standard ID:
JB/T 10120-1999
Standard Name:
Machine tool fixture parts and component clamps
Chinese Name:
机床夹具零件及部件 夹板
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
Original standard number GB/T 12885-1991
Focal point Organization:
Mechanical Science Research InstitutePublishing Department:
Mechanical Science Research Institute
Description (Translated English) / downloadSkip to download
Summary:
JB/T 10120-1999 This standard specifies clamps for workpieces with a diameter of 20 to 150 mm. This standard was first published in 1983 as JB 3394-83 and revised for the second time in 1991 as GB/T 12885-91. JB/T 10120-1999 Clamps for machine tool fixture parts and components JB/T10120-1999 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
IC5 28.060.41
Machinery Industry Standard of the People's Republic of China
The parts and units of jigs and fixtures1999-08-06PromulgatedbzxZ.net
State Machinery Industry Bureau
2000-01-01Implementation
■Scope
Machinery Industry Standard of the People's Republic of China
The parts and units of jigs and fixturesClampplate
This standard specifies the parts applicable to the jigs with a diameter of 20~150mm. 2 Dimensions
The dimensions are shown in the following table.
Small quantity upper piece straight
Nominal diameter
Applicable piece diameter
30-150
Approved by the State Machinery Industry Bureau on August 6, 1999310
JB/T10120-1999
Implementation on January 1, 20100
3 sister notes
3.1 Marking example:
Nominal diameter of 20~100mm plate
1121-—1999
JB.T10120—1999
20~100
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Machinery Industry Standard of the People's Republic of China
The parts and units of jigs and fixtures1999-08-06PromulgatedbzxZ.net
State Machinery Industry Bureau
2000-01-01Implementation
■Scope
Machinery Industry Standard of the People's Republic of China
The parts and units of jigs and fixturesClampplate
This standard specifies the parts applicable to the jigs with a diameter of 20~150mm. 2 Dimensions
The dimensions are shown in the following table.
Small quantity upper piece straight
Nominal diameter
Applicable piece diameter
30-150
Approved by the State Machinery Industry Bureau on August 6, 1999310
JB/T10120-1999
Implementation on January 1, 20100
3 sister notes
3.1 Marking example:
Nominal diameter of 20~100mm plate
1121-—1999
JB.T10120—1999
20~100
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- JB/T 5114-1991 Test method for intermittent sprayers
- GB/T 16306-2008 Re-inspection and re-test procedures for assessment of declared quality levels
- GB/T 15634-1995 Electronic data interchange for administration,commerce and transport (EDIFACT) －Segments directory
- GB/T 33992-2017 Specification for quality information of electronic commerce product
- HG/T 2457-1993 General rules for inspection, marking, packaging, transportation and storage of pigment products
- GB/T 4897.7-2003 Particleboard Part 7: Requirements for reinforced structural boards used in wet conditions
- JB/T 50145-2000 Coordinate-type gas cutting machine product quality classification
- JB/T 10120-1999 Machine tool fixture parts and component clamps
- GB/T 16828-2007 Bar code for commodity—Global location number and symbol marking
- GB/T 19621-2004 Labor quota for urban rail transit light rail projects
- GBJ 304-1988 Ventilation and air conditioning engineering quality inspection and assessment standard GBJ304-88
- SJ 1.5-1987 Provision and requirements for preparation and revision of technical standards for electronic industry-Procedures for review of standards drafs by correspondence
- GB/T 15166.4-1994 General test methods for AC high voltage fuses
- GB/T 3543.3-1995 Crop seed inspection procedure Purity analysis
- WB/T 1045-2012 Drive in-rack
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：wymp4wang@gmail.com