GB/T 3104-1982 Hexagonal fasteners width across flats
time:
2024-08-11 10:01:43
- GB/T 3104-1982
- in force
Standard ID:
GB/T 3104-1982
Standard Name:
Hexagonal fasteners width across flats
Chinese Name:
紧固件 六角产品的对边宽度
Standard category:
National Standard (GB)
-
Date of Release:
1982-05-22 -
Date of Implementation:
1983-07-01
Standard ICS number:
Mechanical systems and general parts >> 21.060 FastenersChina Standard Classification Number:
Machinery>>General Parts>>J13 Fasteners
Release date:
1982-05-22Review date:
2004-10-14Drafting Organization:
Machinery Standards InstituteFocal point Organization:
National Technical Committee for Fastener StandardizationPublishing Department:
China Machinery Industry FederationCompetent Authority:
China Machinery Industry Federation
Description (Translated English) / downloadSkip to download
Summary:
GB/T 3104-1982 Width across flats of hexagonal fasteners GB/T3104-1982 Standard download decompression password: www.bzxz.net
Standard contentSome standard content:
National Standard of the People's Republic of China
Fasteners
Widths across flats of hexagon products
Fasteners --Widths across flats of hexagon products Introduction
UDC 621.882
GB 3104-82
(Confirmed in 1988)
This standard is equivalent to the international standard ISO272-1982 "Fasteners-Width across flats of hexagon products". This standard specifies the width across flats of hexagonal products and is applicable to standard and non-standard fasteners. 2 Dimensions are as specified in Figures 1, 2 and the table.
Thread diameter
Standard series
Enlarged series
Published by National Bureau of Standards on May 22, 1982
Products with flange face
Thread diameter
Standard series
Implementation on July 1, 1983
Thread diameter
Standard series
Enlarged series
3The ratio of bearing surface to stress area is shown in Figure 3. Body and
GB 3104—82
Products with flanged surface
·Hexagonal flange series
Thread diameterbzxz.net
.2-2-.30-
41 ----46 -+-50 --1
55 ----50 Enlarged series
-------
_46--- 50 --- 5 Standard series
M6M8 M10 M12 M14 M16 M18 M20 M22 M24M27M30M33M36
Additional remarks:
This standard was proposed by the Ministry of Machinery Industry of the People's Republic of China. This standard was drafted by the Standardization Research Institute of the Ministry of Machinery Industry. This standard was first issued in May 1982.
This standard was confirmed in April 1988.
Standard Series
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Fasteners
Widths across flats of hexagon products
Fasteners --Widths across flats of hexagon products Introduction
UDC 621.882
GB 3104-82
(Confirmed in 1988)
This standard is equivalent to the international standard ISO272-1982 "Fasteners-Width across flats of hexagon products". This standard specifies the width across flats of hexagonal products and is applicable to standard and non-standard fasteners. 2 Dimensions are as specified in Figures 1, 2 and the table.
Thread diameter
Standard series
Enlarged series
Published by National Bureau of Standards on May 22, 1982
Products with flange face
Thread diameter
Standard series
Implementation on July 1, 1983
Thread diameter
Standard series
Enlarged series
3The ratio of bearing surface to stress area is shown in Figure 3. Body and
GB 3104—82
Products with flanged surface
·Hexagonal flange series
Thread diameterbzxz.net
.2-2-.30-
41 ----46 -+-50 --1
55 ----50 Enlarged series
-------
_46--- 50 --- 5 Standard series
M6M8 M10 M12 M14 M16 M18 M20 M22 M24M27M30M33M36
Additional remarks:
This standard was proposed by the Ministry of Machinery Industry of the People's Republic of China. This standard was drafted by the Standardization Research Institute of the Ministry of Machinery Industry. This standard was first issued in May 1982.
This standard was confirmed in April 1988.
Standard Series
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- GB/T 17726-1999 Protection of small boat electrical installations against ignition of surrounding flammable gases
- JB/T 9388-2002 Technical requirements for single-sided tensiometer
- HG 2011-1991 Rubber Hot Water Bag
- JB/T 6653-1993 Flat steel wire cylindrical helical compression spring
- GB/T 15157.2-1998 Connectors for printed boards with frequencies below 3 MHz Part 2: Detailed specification for two-piece connectors for printed boards with a basic grid of 2.54 mm (0.1 in) and with general mounting features of quality assessment
- GB/T 26443-2010 Safety colours and safety signs—Classification,performance and durability of safety signs
- HG/T 2965-2000 Industrial disodium hydrogen phosphate
- JB/T 2001.63-1999 Filters for water system pumping stations (PN=31.5MPa)
- GB/T 8389-2003 General technical requirements for steel axes
- JB/T 8334.2-1996 CNC turret tool holder horizontal
- HG/T 20701.8-2000 Specification for design of professional equipment diagrams (equipment engineering drawings) for containers and heat exchangers
- GB/T 28227.5-2011 Guidelines for the implementation of the quality management system of cultural service—Part 5:Audio-video products and electronic publications reproductions
- GB/T 15648-1995 Test methods for glow discharge display tubes
- SJ 20015-1992 Semiconductor discrete device-Detail specification for NPN silicon high-frequency low-power transistor for type 3DG130 GP,GT and GCT classes
- QB/T 2025-1994 Lithographic printing ink
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail：bzxznet@163.com