
JB/T 10117.5-1999 Machine tool fixture parts and components clamping type internal cone hole center
time:
2024-08-12 02:17:28
- JB/T 10117.5-1999
- in force
Standard ID:
JB/T 10117.5-1999
Standard Name:
Machine tool fixture parts and components clamping type internal cone hole center
Chinese Name:
机床夹具零件及部件 夹持式内锥孔顶尖
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
1999-08-06 -
Date of Implementation:
2000-01-01
Standard ICS number:
General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)China Standard Classification Number:
Machinery>>Process Equipment>>J44 General Fixture
alternative situation:
Original standard number GB/T 12882-1991
Focal point Organization:
Mechanical Science Research InstitutePublishing Department:
Mechanical Science Research Institute

Skip to download
Summary:
JB/T 10117.5-1999 This standard specifies clamping internal taper centers for workpieces with a diameter of 4 to 95 mm. This standard applies to front centers with pneumatic or hydraulic tailstock lathes. This standard was first published in 1983 as JB 3391-83 and first revised in 1991 as GB/T 12882-91. JB/T 10117.5-1999 Machine tool fixture parts and components clamping internal taper centers JB/T10117.5-1999 standard download decompression password: www.bzxz.net

Some standard content:
IC5 28.060.41
Mechanical Industry Standard of the People's Republic of China
Parts and units of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06Promulgated
State Machinery Industry Bureau
Implementation on 2000-01-01
1Scope
Mechanical Industry Standard of the People's Republic of China
Parts and units of jigs and fixtures
The parts and units of jigs and flurrsHuldiaginnertaperholecentre
The small standard bottle standard is applicable to 1 piece of held internal chain ugly center with a diameter of 4~95mm. 2 Referenced Standards
JR/T10117.5-1999
The above standards contain the specifications, which constitute the content of this standard by reference in this standard. When this standard is revised, the versions shown are valid. All standards are subject to revision, so parties using this standard should consider the possibility of using the latest version of the standard. GD/T1298--1986
JB/T 8044—1999
3 Dimensions
Technical conditions for carbon steel boilers
Technical requirements for machine tools and their components The dimensions are shown in the following table.
Circle Machinery Industry 1999-08-0% Approval 50-
2000-01-01 Implementation
Nominal diameterbzxZ.net
Applicable month 1 Part diameter:
4 - 10
B - 24
56 - 75
701 -93
4 Technical conditions
4.1 Material: T8 in accordance with GB/T1298, 4.2 Heat treatment: 55 -60 HRC
4.3 Other technical conditions in accordance with JB/T8044. 5 Marking
5.! Marking example:
IH/10117.5-1999
Clamp-on internal pin hole with nominal diameter of 22~40mm Original fire: Original tip 22-40JB/10117.5—1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Mechanical Industry Standard of the People's Republic of China
Parts and units of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06Promulgated
State Machinery Industry Bureau
Implementation on 2000-01-01
1Scope
Mechanical Industry Standard of the People's Republic of China
Parts and units of jigs and fixtures
The parts and units of jigs and flurrsHuldiaginnertaperholecentre
The small standard bottle standard is applicable to 1 piece of held internal chain ugly center with a diameter of 4~95mm. 2 Referenced Standards
JR/T10117.5-1999
The above standards contain the specifications, which constitute the content of this standard by reference in this standard. When this standard is revised, the versions shown are valid. All standards are subject to revision, so parties using this standard should consider the possibility of using the latest version of the standard. GD/T1298--1986
JB/T 8044—1999
3 Dimensions
Technical conditions for carbon steel boilers
Technical requirements for machine tools and their components The dimensions are shown in the following table.
Circle Machinery Industry 1999-08-0% Approval 50-
2000-01-01 Implementation
Nominal diameterbzxZ.net
Applicable month 1 Part diameter:
4 - 10
B - 24
56 - 75
701 -93
4 Technical conditions
4.1 Material: T8 in accordance with GB/T1298, 4.2 Heat treatment: 55 -60 HRC
4.3 Other technical conditions in accordance with JB/T8044. 5 Marking
5.! Marking example:
IH/10117.5-1999
Clamp-on internal pin hole with nominal diameter of 22~40mm Original fire: Original tip 22-40JB/10117.5—1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- GB/T 15054.2-1994 Small thread diameter and pitch series
- JB/T 7297-1994 Diesel engine fuel injection nozzle assembly performance test method
- JB/T 8508-1996 Electrical grade magnesium oxide
- JB/T 9039-1999 Electromagnetic double-roller high-intensity magnetic separator
- JB/T 9160.14-1999 Dimensions of post-forming tool holders for single-spindle turret automatic lathes
- JB/T 9882-1999 Accuracy test of side base of modular machine tool
- JB/T 6213.2-1992 Flexible cables and cords for connecting motor windings Part 2 Flexible cables and cords with a maximum continuous operating conductor temperature of 70°C
- CECS : 3892 Code for Design and Construction of Steel Fiber Reinforced Concrete Structures CECS38:92
- JB/T 938-1999 Single-shaft vibrating screen for coal
- JJG 2085-1990 Measuring Instruments for AC Power
- GB 16230-1996 Hygienic standard for isopropyl alcohol in workshop air
- HG/T 2765.1-1996 Silica gel fine pore silica gel
- GB 16915.2-2000 Switches for household and similar fixed electrical installations Part 2: Particular requirements Section 1: Electronic switches
- GB/T 4111-1997 Test methods for small concrete hollow blocks
- GB/T 17140-1997 Determination of lead and cadmium in soil quality - KI-MIBK extraction flame atomic absorption spectrophotometry
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail:bzxznet@163.com