JB/T 9102.4-1999 Metallic flat packings for reciprocating piston compressors Part 4: Radially notched oil scraper rings

JB/T 9102.4-1999 JB/T 9102.4-1999 Metallic flat packings for reciprocating piston compressors Part 4: Radial cut oil scraper rings JB/T9102.4-1999 Standard download decompression password: www.bzxz.net

EC5 23. 140
Machinery Industry Standard of the People's Republic of China
JB/T9102.1~9102.6-1999
Reciprocating piston compressor
Metal plane packing
Reciprocating piston compressor metal rectanglc packing1999-07-12Promulgated
State Machinery Industry Bureau
2000-01-01Implementation
JB/T9102.4—1999
This standard is a revision of ZB172005.487≤Reciprocating piston compressor metal plane radial tangent oil dipstick. The original standard has been edited and the main technical content has not changed. This standard is the fourth part of the JB9102 series of standards for metal plane materials of reciprocating compressors. This series of standards includes the following parts: Part 1: (i.e. JB/T9102.1): Metal plane packing three-angle seal Part 2: (i.e. JB/T9102.2): Metal plane packing three-angle seal Part 3: (i.e. JB/T9102.3) Metal plane packing three-angle seal Part 4: (i.e. JB/T9102.4) Metal plane packing radial notch oil scraper ring Part 5: (i.e. JB/T912.5): Metal plane packing seal ring and oil scraper ring technical specifications Part 6: (i.e. JB/9102.6): Metal plane packing and standard from the date of implementation to replace July 3, 2005.4-87. This standard is proposed and managed by the National Technical Committee for Standardization of Reciprocating Compressors. The main drafting unit of this standard is Zongyang Compressor Factory. The main responsible persons for drafting this standard are Bai Fujing, Feng Quanke and Shen Mingyao. 15 [Scope] Machinery Industry Standards of the People's Republic of China Metal plane packing Reciprocating piston compressor Part 4: Radical cut wiper Reciprocating piston compressarmetal rectaglepackiag-Part4: Radical cut wiper iagsJB/T9102.4—1999 ZB 172 C05.4—87 This standard specifies the classification and size, matching specifications and relevant requirements of metal plane radial cut wipers (hereinafter referred to as radial cut wipers) of reciprocating piston compressors. This standard is applicable to radial cut wiper rings. 2 Reference standards
The provisions contained in the following standards are reduced to substandard provisions by reference in this standard. This standard is valid for the versions shown. All standards will be revised. The parties using this standard should consider the compatibility of the latest versions of the following standards. JB/T9JU2.3-.1999 Pump compressor gold mesh flat packing Part 3: Lanzhou, hexapod sealing ring JB/T9102.51999
Reciprocating piston compressor gold wine flat block Part 5: Tension spring for sealing ring and oil scraper ring JB/T9[02.61999 Reciprocating piston stopper gold flat packing Part 6: Technical conditions for sealing ring and oil scraper 3 Classification and size
The warp cut oil scraper is divided into two types: A type and Japanese type. 3. The size, surface roughness and matching material of type A radial moving mouth profit circle shall comply with the requirements of Figure 1 and Table 1. Approved by the National Machinery Industry Bureau on July 12, 1999 and implemented on January 1, 204. Marking: IB/T 9102.4—1999 The internal diameter of the radial cut scraper with a diameter of 4Sm is marked as radial cut scraper 45-AJB/T9102.4—[999 Table 1 Basic limit deviation (55) 10 014
Basic size limit
Note: The values ​​in brackets are limited to the use of old products134
3.1B radial cut oil scraper size, surface roughness and matching spring should comply with the provisions of Figure 2 and Table 2. Rim
Capacity
JT 9102.5
05×3×9
0.5 ×3 × 106
0.5×3×115
3.5×3 ×127
0.5×3×137
0.8 × 4 × iB9
0.8×1×203
n8×4×217
0.8×4 ×243
0.8 ×4 ×256
184×275
8×4×3
1×5x316
1k5×34]
1-5368
h-5×47
1k5×547
Marking example:
[8/9102.4-1999
The B-type radial cut oil scraper ring with an inner hole diameter of 45mm is marked as radial expansion 45-BJB/T9102.419992
The basic size is 24
56 higher than the wind position difference 60
Marking position
System method
Matching material
JBrr9102.5wwW.bzxz.Net
U.5×3 × road
0.5 ×3 × 106
0.5×3×115
0 5 x3 127
0.3 ×3 ×137
0.8×4×189
0.8 × 4×203
.8×4×217
0.8×4×243
0.8×4×256
Hua state can be unlimited if the principle of the lead pole is replaced by the difference 7u
+0 018
Companion: The values ​​in brackets are limited to the use of old products. 4 Pairing requirements
JBT9[024-1999
Table (complete)
4.1 The radial cut scraper is used in pairs and is used in conjunction with the large sealing valve specified in BT9102.3. 4.2-The assembly position of the A-type radial cut scraper in the packing is in accordance with the provisions of Figure 3, and the parts in the figure are in accordance with the provisions of Table 3. Figure 3
A type light tangential oil scraper
Pulling type
Standard number
[B/T 9102.5
4.3The assembly position of B type radial oil scraper in the filling section shall be in accordance with the provisions of Figure 4, and the linearity in the figure shall be in accordance with the provisions of Table 4, mm
Matching width
G.3 x4 × 275
0.8×4× 300
1-5-916
1x5-341
Jx×368
1-5×407
1-5×447
5Technical conditions
JB/T 9102.4—1999
Stretched elastic tube
Radial scratching [1 Scraping pool ring technical conditions according to the provisions of JB/T9102.6, 21
Zongzhou No.
3B/9102.4
JB/T91025
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.