JB/T 10410-2004 Automatic backwash filter for industrial water

This standard specifies the types and basic parameters, technical requirements, test methods, inspection rules, marking, packaging, transportation, storage, quality assurance period and other requirements of industrial water filters. This standard applies to industrial water automatic backwash filters with filter media installed in industrial containers and a filtration accuracy range of 0.005mm~6mm. JB/T 10410-2004 Industrial Water Automatic Backwash Filter JB/T10410-2004 Standard download decompression password: www.bzxz.net

1CS73.120
Machinery Industry Standard of the People's Republic of China
JB/T 10410-2004
Back wash filter for industry waten2004-02-10 release
2004-06-01 implementation
The National Development and Reform Commission of the People's Republic of China issued the following statement
Current standard document
4 type and integer
Model table method
Structural type
Basic technical effect,
Technical requirements.
Performance requirementsbzxz.net
Structural requirements
Material separation of components
Manufacturing requirements
Appearance vertical type
Safety requirements
Test method.
Kerosene leakage test
Water positive test chamber
|Rotation test
Rotation test,
Load test
Basic requirements
Inspection classification
Inspection items
Idle running test
Load running test
Marking, installation, transportation and storage
New warranty period.
Electric sewage type 1 Industrial water self-effect zone flushing filter structure diagram 2
Manual sewage type Industrial water automatic backwashing filter structure diagram. JB/T10410—2004
JB/T10410—-2004
This standard is the first to formulate
This standard is the Machinery Industry Federation! !
This standard is under the jurisdiction of the National Technical Committee for Standardization of Separation Machinery. The drafting unit of this standard is Gaote Filter Manufacturing Co., Ltd. The main drafters of this standard are Qiu Changchun, Wang Jianshou, Wen Chengxing, Chuan Liaoqin and Yang An. TE
1 Fan Guo
Automatic backwash filter for industrial water
[R/T 1941U—2004
This environmental standard specifies the basic parameters, technical requirements, inspection points, inspection center, source, packaging, transportation storage, warranty period and other requirements for industrial water filters.
This standard applies to industrial water automatic flushing material filters (hereinafter referred to as reverse flow filters) installed in industrial containers with a filter belt width of 0.005m~611n.
2 Normative references
The clauses in the following documents are quoted as references to the standards. For any dated document, all subsequent amendments (excluding the internal wear of the dynamic) or modifications are applicable to this standard. However, the parties who have reached or cooperated with this standard are encouraged to use the latest versions of these documents. For any undated referenced documents: the latest version applies to this standard: CB15 price 195% steel! Steam container| |tt||CD/T191-200 Shipping drawing Beijing standard Hui e [S07: 1997C1R structure I6O: 19)
GH-T: 225
GHT2190
GR/13677
Stainless steel copper castings
General purpose corrosion-resistant key castings
Taiwan gold shrinkage steel
GB/T3280—1992 Stainless steel cold rolled steel plate G B5226.12002 Safety of machinery - Electrical equipment - Part 1: General connection - Technical specifications (1C6204.1.9Y2.1DTG9/1636$-136G
GD:T9439-1988
Transport packaging - Receiving and dispatching freight transport information
Gray cast iron parts
Separation of mechanical noise - Determination of the ratio level - T process method (nea1%>3744:1981:GL-T 10891 1939
G/T113521989
(HT133199:
GH/T 13384—13P2
General engineering casting requirements (nnet 130) 1755: 1975) brand
General technical system for packaging of electromechanical products
Testing of water treatment equipment
GB/T13422.3—12
Stainless steel seamless steel pipe for fluid conveying
GB/149?6?
JB/-72!7—1994 General technical system for mechanical coating of sealing parts 72 Simple large pressure filter
JH/T729
Extract type pressure filter specification Leakage test method H939—1999 Safety technical specification for water pollution prevention equipment 3 Definition||tt ||This standard defines:
Industrial water backwash filter-a water filter that filters the impurities in the industrial water passing through the industrial wastewater to purify the water:
Type and technical parameters
41. Model representation method
/T104102004
A.1.1 The model number of the filter shall comply with the following regulations 4.1.2 Marking example
Retrofit number: A, D,...
Inlet and outlet diameters, inner diameter of the water filter shell,
Electric sewage discharge type: P
Manual sewage discharge type: S
Automatic backwash filter for industrial water: 1.2! Industrial water automatic backwash filter, electric drainage type, inlet and outlet diameter is 100mm, the inner diameter of the filter element is 500mm. LIOS electric sewage type industrial water automatic backwash filter. h) "Industrial water automatic backwash flow through the dream hip, dynamic sewage type, inlet and outlet diameter is 50mm, the inner diameter of the filter element is 250TL50/25 manual drainage type 1 Industrial water automatic backwash test filter 4.2 Structural type
a) Electric sewage type industrial water automatic backwash filter (L type) see Figure "b) Dynamic non-sewage type industrial water automatic backwash filter (LS type) see Figure 2, 2
Figure 1 Electric sewage type industrial water automatic backwash filter structure diagram 2 Manual sewage type industrial water automatic backwash filter structure diagram 4.3 Basic parameters
Filtering technology parameters conform to the provisions of the ensemble 1. Basic Model
Appropriate inlet diameter
Throughput
Flow: The filter force in the table refers to the inlet and outlet pressure when the pressure is U2MPu and the flow rate is m. 5 Technical requirements
Jn.T10410—2004
Throughput accuracy
The filter should comply with the provisions of this standard: Design and manufacture shall be in accordance with the drawings and technical documents approved by the specified order: The design and manufacture of the filter shall meet the following requirements.
b1 Performance requirements
511 The filter shall have a filtering capacity, flow rate and precision, and meet the design requirements. The precision is preferably within the range of 0.05mm1-0.1mm. The requirements of B/T219 shall be included.
51.2 When the electric filter is running empty and under load, the oil temperature of the reducer shall not be greater than 6.513 When the electric filter is running empty and under load, the noise (pressure level) shall not exceed 786 (A) 5.1.4 The filter accuracy and filter capacity of the filter shall meet the design requirements. JH 10410-2004
5.1.5 Under normal use of the filter, the half-average time without fault workpieces after deducting the time for replacement shall not be less than 8C1: 5.2 Structural requirements
5.2.1 The filter shall be equipped with a water outlet 5.2.2 The filter should be assembled as a whole. 5.2.3 Each seal should be equipped with a disconnect device. The filter should be equipped with a force indicator and a filter element blockage warning ticket. 5.2.4
5.2.5 The filter element should have a fineness that is sufficient for the filter element. 5.3 Material requirements for main parts
5.3.1 The material of the filter should comply with the provisions of the current standards and have a test certificate: 5.3.2 The pin iron parts should comply with the provisions of G1:79439. 5.3.34
The steel castings should comply with the provisions of (H/T11352 or GB/121U0, 5.34 The shaft parts should comply with
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.