
JB/T 8830-2001 Calculation method for load-bearing capacity of high-speed involute cylindrical gears and similar gears
time:
2024-08-14 16:41:09
- JB/T 8830-2001
- in force
Standard ID:
JB/T 8830-2001
Standard Name:
Calculation method for load-bearing capacity of high-speed involute cylindrical gears and similar gears
Chinese Name:
高速渐开线圆柱齿轮和类似要求齿轮 承载能力计算方法
Standard category:
Machinery Industry Standard (JB)
-
Date of Release:
2001-05-23 -
Date of Implementation:
2001-10-01
Standard ICS number:
Mechanical systems and general parts >> 21.200 Gears and gear transmissionsChina Standard Classification Number:
Machinery>>General Parts>>J17 Gears and Gear Drives
alternative situation:
JB/T 8830-1999Procurement status:
idt ISO 9084:1998

Skip to download
Summary:
JB/T 8830—2001 JB/T 8830-2001 Calculation method for load capacity of high-speed involute cylindrical gears and similar gears JB/T8830-2001 Standard download decompression password: www.bzxz.net

Some standard content:
ICS21.200
Machinery Industry Standard of the People's Republic of China
JB/T 8830-2001
idt1S09084:1998
Calculation of load capacity for high speed gears and gears of similar requirements2001-05-23 Issued by China Machinery Industry Federation on October 1, 2001 and implemented by JE.T88302001 [5O Foreword J80 Introduction 2 Reference standards 3 Main codes 4 Load influence coefficient 5 Calculation of surface contact strength (point passing) 6 Calculation of gear bending strength Appendix A (Appendix to standard) Gear tooth stiffness and core strength Appendix A (Appendix to standard) Appendix C (Tyr's Appendix) Appendix D (Suggestive Appendix]
Multiple Reference Documents
JI/T8830-2001
This standard is equivalent to 1SO90B4:1998 "Calculation of load capacity of straight and inclined gears: - Application standard for high-speed gears and similar gears", and the revision of JB/18830-999 high-speed involute gear load capacity calculation method. This standard is equivalent to B Compared with 1999, the following aspects have been revised: 1. In the scope of chapter 1, the design of gears and the application fields are expanded; 2. According to 1S9084: [998, the calculation formula of dynamic section coefficient K is modified; 7. In the calculation formula of contact stress, the combined coefficient 2Z of small and large gear teeth is added; 4. The calculation formula of allowable connection and allowable tooth root is increased and increased respectively; 5. In the two sections of material contact and bending fatigue limit, the four value lines of MX, ME, MQ and ML are used instead of JB/TBB30-19. 9g's Hall According to the drama:
6. In Appendix A (Appendix of the standard), a more detailed calculation method for gear tooth stiffness e: and c is given. In Appendix B (Standard Appendix), the dynamic load coefficient of the test gear with unconventional design (planetary gear transmission, split transmission) and the calculation formula of the tooth load coefficient of some products are given. In Appendix C (Informative Appendix), the use coefficient, the promotion value of the inverse coefficient, and the formula are also adjusted according to IS09084:1998: 4. The standard replaces JB/T8830-1999 from the date of implementation. Appendix A and Appendix B of this standard are standard appendices; Appendix C and Appendix D are informative appendices. This standard is proposed and managed by the National Gear Standardization Technical Committee. This standard is initiated by Zhengzhou Machinery Research Institute. The main drafters of this standard are Zhang Yuanguo, Zhang Ju'an, Hui Donghai, Chang Xingyuan, Wang Fu, Yan Guang. This standard was first issued in September 1990 as TF17006-90, and the standard number was changed to JB8830.1999 in April 1999. This is the second revision.
JB/F8830-2001
ISO Foreword
ISO6336 Parts 1, 3, and 3 give the calculation method for the load capacity (contact strength and bending strength) of spur gears and helical gears. In the above standards, the assumptions related to the calculation method are also quoted in this standard. The influence coefficients in this international standard are derived from 1306336-1, and this standard uses the fatigue limit values in IS06336-5. This International Standard consists of four annexes:
Annex A is a normative annex and contains information and formulas for the number of tooth stiffness bars required for the calculation of the lateral bending strength of gear teeth.
Annex B is a normative annex and contains information and formulas for the determination of the load factor and the tooth load distribution factor required for the strength calculation of gear teeth of non-conventional designs.
Annex C is a general annex and gives recommended values of the recovery factor.
Annex D contains a list of other international standards not mentioned in this standard and which may not be useful to the reader. This International Standard is based on FC60/ISO 2. Chapter
ISO Introduction
This International Standard is derived from ISO 6336 Parts 1, 2 and 3 and has been simplified in some respects. The assumptions made in Parts 1, 2 and 3 of ISO 6336 are applicable to the calculation methods of this International Standard. The material strengths and qualities given in ISO 6336-5 are valid for this standard. If more detailed calculations are required or if the restrictions of 1.2 and 1.3 cannot be met for various reasons, the relevant coefficients may be calculated on the basis of the basic standard or some other performance standard. Coefficients obtained from reliable experience or test data may replace the corresponding coefficients calculated in accordance with this standard. In this regard, the standard of ISO 6336-1A method 1.9 may be used. All differences must be recorded in the calculation statement. If the strength, safety factors, etc. are calculated in accordance with 150904, the other aspects of the strength calculation must be strictly carried out in accordance with this standard. The information exchanged between the manufacturer and the user should include material properties, lubrication, safety factors and external forces caused by internal and external forces (service factors).
In all calculations, the units listed in Chapter 3 must be used. The information given in Annexes A and C of ISO 63361 will facilitate the use of technical standards.
Machinery Industry Standard of the People's Republic of China
Calculation method for load capacity for high speadgears ind gears of similar reyuiremenis1.1 rangebZxz.net
JB/A830-2001
Tdt IS09084:1998
JB8830-1999
This standard specifies the calculation method of the tooth contact strength (tip) and wheel curvature of high-speed involute spur gears suitable for transmitting the total torque through a single gear pair.
The calculation of the gluing load capacity of involute spur gear teeth is not included in this standard. The gluing load capacity of gears is calculated in accordance with GB 6413.
1.2 Application
This standard applies to:
ar tooth type
integral, perfect meshing involute spur, helical and double group gears; for double helical gears, the total shear force is limited to The grooves are densely distributed on the saber teeth on both sides. If this is not the case, the tree has an external non-directional effect! When the new teeth on both sides must be arranged according to two parallel single helical gears, they are not considered: -Multi-branch transmission and other gear systems. b) Speed range
Pulley speed net 300min (synchronous speed of the two-pole motor at 50H current. It is also suitable for low-precision gears with special requirements.
When the loop line speed is 1m, the gear load capacity is limited by the loss.) Gear precision
GBT10095 is now complete with 5 or higher precision grades (Bin Ky, K, K, Ked? Equivalent spur gear brush end and overlap range 1.2
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
Machinery Industry Standard of the People's Republic of China
JB/T 8830-2001
idt1S09084:1998
Calculation of load capacity for high speed gears and gears of similar requirements2001-05-23 Issued by China Machinery Industry Federation on October 1, 2001 and implemented by JE.T88302001 [5O Foreword J80 Introduction 2 Reference standards 3 Main codes 4 Load influence coefficient 5 Calculation of surface contact strength (point passing) 6 Calculation of gear bending strength Appendix A (Appendix to standard) Gear tooth stiffness and core strength Appendix A (Appendix to standard) Appendix C (Tyr's Appendix) Appendix D (Suggestive Appendix]
Multiple Reference Documents
JI/T8830-2001
This standard is equivalent to 1SO90B4:1998 "Calculation of load capacity of straight and inclined gears: - Application standard for high-speed gears and similar gears", and the revision of JB/18830-999 high-speed involute gear load capacity calculation method. This standard is equivalent to B Compared with 1999, the following aspects have been revised: 1. In the scope of chapter 1, the design of gears and the application fields are expanded; 2. According to 1S9084: [998, the calculation formula of dynamic section coefficient K is modified; 7. In the calculation formula of contact stress, the combined coefficient 2Z of small and large gear teeth is added; 4. The calculation formula of allowable connection and allowable tooth root is increased and increased respectively; 5. In the two sections of material contact and bending fatigue limit, the four value lines of MX, ME, MQ and ML are used instead of JB/TBB30-19. 9g's Hall According to the drama:
6. In Appendix A (Appendix of the standard), a more detailed calculation method for gear tooth stiffness e: and c is given. In Appendix B (Standard Appendix), the dynamic load coefficient of the test gear with unconventional design (planetary gear transmission, split transmission) and the calculation formula of the tooth load coefficient of some products are given. In Appendix C (Informative Appendix), the use coefficient, the promotion value of the inverse coefficient, and the formula are also adjusted according to IS09084:1998: 4. The standard replaces JB/T8830-1999 from the date of implementation. Appendix A and Appendix B of this standard are standard appendices; Appendix C and Appendix D are informative appendices. This standard is proposed and managed by the National Gear Standardization Technical Committee. This standard is initiated by Zhengzhou Machinery Research Institute. The main drafters of this standard are Zhang Yuanguo, Zhang Ju'an, Hui Donghai, Chang Xingyuan, Wang Fu, Yan Guang. This standard was first issued in September 1990 as TF17006-90, and the standard number was changed to JB8830.1999 in April 1999. This is the second revision.
JB/F8830-2001
ISO Foreword
ISO6336 Parts 1, 3, and 3 give the calculation method for the load capacity (contact strength and bending strength) of spur gears and helical gears. In the above standards, the assumptions related to the calculation method are also quoted in this standard. The influence coefficients in this international standard are derived from 1306336-1, and this standard uses the fatigue limit values in IS06336-5. This International Standard consists of four annexes:
Annex A is a normative annex and contains information and formulas for the number of tooth stiffness bars required for the calculation of the lateral bending strength of gear teeth.
Annex B is a normative annex and contains information and formulas for the determination of the load factor and the tooth load distribution factor required for the strength calculation of gear teeth of non-conventional designs.
Annex C is a general annex and gives recommended values of the recovery factor.
Annex D contains a list of other international standards not mentioned in this standard and which may not be useful to the reader. This International Standard is based on FC60/ISO 2. Chapter
ISO Introduction
This International Standard is derived from ISO 6336 Parts 1, 2 and 3 and has been simplified in some respects. The assumptions made in Parts 1, 2 and 3 of ISO 6336 are applicable to the calculation methods of this International Standard. The material strengths and qualities given in ISO 6336-5 are valid for this standard. If more detailed calculations are required or if the restrictions of 1.2 and 1.3 cannot be met for various reasons, the relevant coefficients may be calculated on the basis of the basic standard or some other performance standard. Coefficients obtained from reliable experience or test data may replace the corresponding coefficients calculated in accordance with this standard. In this regard, the standard of ISO 6336-1A method 1.9 may be used. All differences must be recorded in the calculation statement. If the strength, safety factors, etc. are calculated in accordance with 150904, the other aspects of the strength calculation must be strictly carried out in accordance with this standard. The information exchanged between the manufacturer and the user should include material properties, lubrication, safety factors and external forces caused by internal and external forces (service factors).
In all calculations, the units listed in Chapter 3 must be used. The information given in Annexes A and C of ISO 63361 will facilitate the use of technical standards.
Machinery Industry Standard of the People's Republic of China
Calculation method for load capacity for high speadgears ind gears of similar reyuiremenis1.1 rangebZxz.net
JB/A830-2001
Tdt IS09084:1998
JB8830-1999
This standard specifies the calculation method of the tooth contact strength (tip) and wheel curvature of high-speed involute spur gears suitable for transmitting the total torque through a single gear pair.
The calculation of the gluing load capacity of involute spur gear teeth is not included in this standard. The gluing load capacity of gears is calculated in accordance with GB 6413.
1.2 Application
This standard applies to:
ar tooth type
integral, perfect meshing involute spur, helical and double group gears; for double helical gears, the total shear force is limited to The grooves are densely distributed on the saber teeth on both sides. If this is not the case, the tree has an external non-directional effect! When the new teeth on both sides must be arranged according to two parallel single helical gears, they are not considered: -Multi-branch transmission and other gear systems. b) Speed range
Pulley speed net 300min (synchronous speed of the two-pole motor at 50H current. It is also suitable for low-precision gears with special requirements.
When the loop line speed is 1m, the gear load capacity is limited by the loss.) Gear precision
GBT10095 is now complete with 5 or higher precision grades (Bin Ky, K, K, Ked? Equivalent spur gear brush end and overlap range 1.2
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.
- Recommended standards
- HG/T 20552-1994 Chemical water treatment design and calculation regulations for chemical enterprises
- JB 20023-2004 Aluminum plastic blister packaging machine
- JB/T 3242-1993 SWZ type integral bearing seat cross shaft universal coupling
- JB/T 7890-1999 Fan coal mill
- MT/T 951-2005 Coal Classifying Crusher
- GB/T 5413.9-1997 Determination of vitamin A, D and E in infant formula and milk powder
- GB/T 5070.1-2002 Chemical analysis methods for magnesia-chromium refractories Part 1: Gravimetric determination of loss on ignition
- GB/T 3047.3-2003 Basic dimension series of plug-in boxes and plug-ins with a height of 20 mm
- YS/T 462-2003 Copper and copper alloy tube, rod and wire product defects
- JGJ 65-1989 Safety technical regulations for construction of hydraulic sliding formwork
- JB/T 6891-1993 Technical specifications for silencers for fans
- GB 12141-1989 Safety specification for freight aerial ropeways
- GB/T 11617-1989 Lexicographical symbols
- JB/T 6914-1993 Automobile air conditioner performance test method
- QB/T 3709-1999 Thread take-up cam for household sewing machines
Please remember: "bzxz.net" is the combination of the first letters of the Chinese pinyin of the four Chinese characters "standard download" and the international top-level domain name ".net". ©2024 Standard download websitewww.bzxz.net Mail:[email protected]