GB/T 9146-2003 Limit dimensions of common thread roughness and preferred series

This standard specifies the roughness, preferred series, and the limit sizes of the middle diameter and top diameter of coarse thread according to the basic deviations and tolerances of GB/T9144-2003 and GB/T197-2003. The basic tooth profile of ordinary thread complies with the provisions of GB/T192-2003 and is suitable for general-purpose mechanical fastening threaded connections. The thread itself does not have a sealing function. GB/T 9146-2003 Limit sizes of roughness and preferred series of ordinary thread GB/T9146-2003 Standard download decompression password: www.bzxz.net

This standard is different from B3, and the size specification has changed. The effective nominal diameter range in the standard text is 1mr-39mm, and the rated diameter range is 42m~m. The measured screw grade is A (reference part, while the effective nominal diameter in the standard text is mm61nmar. This standard is the limit size of the entire effective series standard. The standard package for the screw effective series is 20.
GS/T IS2
Taiwan
63/T 153-2004
G3/T$144
- -.-5/1 1411—2004
CET 16
G3/T 15?-200.1
GHT2516
Old oil explosion lock
Ordinary required pattern
General frequency pattern
World common drink
(3/r 15755-195
t+H:7 9115
Base type:
True diameter and module distance series 3
Select the system judgment:
Some road series:
Base people:
Tolerance
Limit error:
Ordinary exhaust pattern
Ordinary effectbzxZ.net
Dial limit size 3
Order accuracy is excellent, the limit size is excellent, the relative accuracy is excellent This standard was proposed by the Standardization Technical Committee (SAI) under the supervision of the Ministry of Industry and Information Technology. The responsible drafting unit of this standard is the Institute of Mechanical Engineering. The main drafters of this standard are Li Xiaobin, Changle Standard 1988, General thread roughness accuracy, preferred series limit size TA/T9146-2003 This standard According to the G/T9:442005 system and GB19?203 basic assumptions and tolerances, the diameter and diameter of the thread of the corresponding ordinary thread (-thread thread) are determined. The effective cost technology conforms to the provisions of G/T192-20G. The machine used for general belt fastening is used for the joint compensation, and its ticket has no sealing function: 2 Normative references The following documents The clauses in this document become the clauses of this standard through reference. All the referenced documents in the specified period are subject to the revision of the standard (excluding the revision of the content or revision of the standard). However, the parties are encouraged to study whether the latest version of this document can be used: the latest version of this standard is the reference of the technical juice mountain period, and the latest version is applicable to this standard 193 general text base 43-199810ws
Basie prozileFart :.Mc.tri: ecrew thareade,MloD)s:Toy--2nos纹公美（I)e1Wx,lsu)ganeralpurpnaemeurie scrrwihrea:lgTu'crenxsPurt -.P-ituigkes une busie dutu,MoD!G91—2005Ordinary screw effect light transmission system:1S026Oelmerrth:eecsSelected sizes ur acrews.bulte and nits.MioD?G:Dry teaching language (nes5o6)
3 Definition of terms
GB/T1-791 specifies the terms and conditions for use in wood standards: 4 Solution mark
Help effect mark, small method into G:T19720U the first R rate. 5 Limit size
Inside and outside the bottom wheel, any point on the bottom wheel should not exceed the maximum actual shape determined by the basic wood type and tolerance position. Unless otherwise specified, the belt is used except for the pre-adjustment screw effect. After adjustment, any point on the bottom wheel should not exceed the actual shape determined by the tolerance belt H.
Juice: These belts are suitable for thin-coated versions. Example key thread, 5.1 coarse pitch inner end groove
public examination viscosity: pile:
comprehensive length: middle school;
relative thread internal thread mouth light and small limit size small use table: GB/T 9146-2003
5.2 coarse pitch outer groove
tolerance pull shop: Shang box:
including length, medium:
tolerance: 8k:
Yingtai long expensive
rental thread internal thread diameter and minor diameter limit size + diameter
4, 543
14, 966
15, 655
s. hit: si
2a, 277
J0, 727
3r, 40:
and special child technique
.u.c35
2h, 921
57 5G5
The maximum and minimum dimensions of the outer diameter and diameter of the tooth are shown in Table 2. Table 2 The maximum and minimum dimensions of the outer diameter and diameter of the tooth are shown in Table 2. 947
nb,985
About the seventh standard of CB/T:672903 and Table V:11.54!
29,277
32,277
tB/T9146—2003
Unit is meter
Doudian effect
18,069
24, 688
G, 625
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.