QB/T 1446-1992 ZNW Gravity Cylinder Thickener

This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation, storage, etc. of ZNW gravity-type round screen thickener (hereinafter referred to as thickener). This standard applies to ZNW gravity-type round screen thickener for papermaking with metal or plastic round screen and metal or cement tank. Other types of round screen thickeners not listed in this standard can be implemented as a reference. QB/T 1446-1992 ZNW gravity-type round screen thickener QB/T1446-1992 Standard download decompression password: www.bzxz.net

Light Industry Industry Standard of the People's Republic of China
ZNW Gravity Cylinder Thickener
1 Subject Content and Scope of Application
QB/T 1446---1992
This standard specifies the product classification, technical requirements, test methods, inspection rules and marking, packaging, transportation, storage, etc. of ZNW Gravity Cylinder Thickener (hereinafter referred to as thickener). This standard applies to ZNW Gravity Cylinder Thickener for papermaking with metal or plastic cylinder and metal or cement tank. Other types of cylinder thickeners not listed in this standard can be implemented as a reference. Reference Standards
QB/T842.1～842.8 General Technical Conditions for Light Industry Machinery Scales 3 Product Classification
According to the different transmission structure arrangements, thickeners are divided into right-hand machine (Y type) and left-hand machine (Z type). Standing at the pulp outlet, facing the concentrator, the transmission is Y-type on the right side and Z-type on the opposite side. 3.2 Model
Concentrator model description:
3.3 Basic parameters
Right handpiece
Concentrator design sequence code, expressed in Arabic numerals Round screen concentrator code
Washing and concentrating equipment code
Papermaking machinery professional code
The basic parameters of the concentrator are shown in Table 1.
Nominal cylinder screen area, m2
Inlet pulp concentration, %
Outlet pulp concentration, %
Production capacity (dry pulp)
t/d?m2
Rice and wheat straw pulp
Chemical wood pulp
Approved by the Ministry of Light Industry of the People's Republic of China on February 21, 1992
2.5～3.5
Name category marking Industry information, free download
Implementation on August 1, 1992
Cylinder screen specifications, mm
(diameter×surface width)
Cylinder screen speed, r/min
Main motor power, kw
4 Technical requirements
4.1 General requirements
Φ1 250×
QB/T1446-
—1992
Continued Table 1
$1 500x
$1500x
$1500x
$2000x
$2500×
Jo. 97 ~9. 75
4.1.1 The thickener shall comply with the provisions of this standard and be manufactured according to the drawings and technical documents approved by the prescribed procedures. 4.1.2 The manufacture of the thickener shall comply with the relevant provisions of QB/T842.1~842.8. 4.2 Product performance
4.2.1 The thickener shall be able to adapt to the dehydration and concentration of various slurries, and its production capacity, inlet and outlet slurry concentrations shall comply with the provisions of Table 1. 4.2.2 Requirements for the operation performance of the concentrator
The round screen should run smoothly within the specified speed range and be able to strip the slurry smoothly; the sealing belt should be reliably sealed and there should be no leakage; b.
The water spray pipe and the discharge spiral should work normally, and the screen surface should be clean after cleaning. 4.3 Processing and manufacturing quality
4.3.1 Metal trough
The inner wall weld should be continuous, smooth and flat; the difference in the diagonal length of the top surface should not exceed the requirements of Table 2; the two planes of the bearing seat should be on the same plane, and the relative height difference should not exceed 3mm. Table 2
Difference in the diagonal length of the top surface of the trough
Radial runout of the outer circle of the screen wheels on both sides of the round screen
4.3.2 Round screen
a. The radial runout of the outer circle of the mesh wheels on both sides and the outer circle surface contacting the sealing tape shall not exceed the requirements of Table 2; b. The straightness of the outer circle surface of the metal round screen is 1mm between the two mesh wheels and not more than 2mm in the whole length; the injection molded filter plate of the plastic round screen should fit closely with the mesh wheel, and the outer circle surface should be flush, without obvious concave and convex. The straightness of the outer circle surface is not more than 3mm in the whole length.
4.3.3 The pressure roller should be calibrated for static balance, and the residual imbalance on the roller surface shall not exceed 0.001 of its own weight. 4.4 Assembly quality
4.4.1 The assembly accuracy of the part of the round screen that contacts the sealing tape (moving circle) and the part of the tank that contacts the sealing tape (static circle): a. The mutual position difference of the outer circles of the two circles along the radial direction is not more than 2mm; b. The axial clearance of the end faces of the two circles is 2~~8 mm, and the variation of each end is not more than 4 mm. 4.4.2 After the general assembly, loosen the sealing tape and the sealing box, and turn the round screen and the pressure roller by hand. The rotation should be light and flexible without blocking. 4.5 No-load running quality
4.5.1 When the sound level meter is used to measure the noise, the sound pressure level limit value shall not be higher than 85dB(A). 4.5.2 The temperature rise of the main bearing shall not be higher than 20℃.
4.6 Appearance quality
Quasi-photography special network
All-school standard industry information science and technology fee one load
6—1992
QB/T1446-
4.6.1 The assembly joint surface of the exposed parts should not have obvious displacement. 4.6.2 There should be no burrs on the exposed cutting edge. 4.6.3 The paint coating should comply with the provisions of QB/T842.7. 4.7 A protective cover should be set at the gear transmission of the concentrator. 5 Test method
5.1 The product performance test shall be carried out in the user's factory according to the commonly used inspection specifications of paper mills. 5.2 Measurement of the difference in length of the diagonal lines of the top opening of the trough
Measure the length of the two diagonals of the trough at the top opening of the trough with the same tape measure, and the difference between them is the difference in length of the diagonal lines of the top opening of the trough. 5.3 Measurement of the relative height difference between the two planes of the bearing seat installed on the trough Place the trough on a plane, measure the height dimensions h1 and h2 of the - side plane along the axis of the main shaft on the bearing plane, and then measure the height dimensions h3 and ha of the bearing seat plane on the other side. The difference between the maximum and minimum values ​​of hl~h is taken as the relative height difference between the two bearing seat planes. 5.4 The difference between the outer circle dimensions of the round screen is measured with a depth caliper; the axial clearance is measured with a vernier caliper or a thickness gauge. 5.5 The static balance of the pressure roller should be carried out on a guide rail static balance device. 5.6 The appearance quality is measured by visual inspection.
5.7 Idle running test
The continuous idle running test time of the concentrator shall not be less than 1h, and the speed shall be from low to high during operation; the sound level meter shall be 1m away from the product, the measuring height shall be 1.5m, and 4 measuring points shall be arranged on the central axis of the concentrator, and the maximum value shall be taken as the actual measured value; b.
Use a thermometer to measure the bearing temperature rise on the surface of the main bearing seat. c
6 Inspection rules
6.1 Factory requirements for concentrators
The concentrator shall be inspected and qualified by the inspection department of the manufacturer and shall be accompanied by a product certificate before it can be shipped. 6.2 Inspection classificationWww.bzxZ.net
The inspection of concentrators is divided into factory inspection and type inspection. 6.3 Delivery inspection
6.3.1 The concentrator shall be inspected for delivery in the manufacturer one by one. 6.3.2 The inspection results of processing, manufacturing and assembly quality shall comply with the provisions of Articles 4.3 and 4.4. 6.3.3 The appearance quality inspection results shall comply with the provisions of Article 4.6. 6.3.4 The idle running test shall be carried out in accordance with Article 5.7, and the test results shall comply with the provisions of Article 4.5. Only one concentrator per batch is allowed to be inspected. 6.4 Type inspection
6.4.1 Type inspection shall be carried out when new products are trial-formed and old products are transferred to the factory for production or when the superior quality supervision agency makes a request. 6.4.2 Type inspection items and requirements
a. The sample for type inspection shall be randomly selected from the products that have passed the factory inspection. b. The product performance test shall be carried out in the user's factory, and the results shall comply with the provisions of Article 4.2. Generally, a typical pulp type performance test is carried out. 7 Marking, packaging, transportation, compensation and storage
7.1 Marking
Each concentrator shall have a product nameplate fixed in a conspicuous position, which shall include: product name and model;
b. Main technical parameters;
c. Factory number and date:
Quasi-search special network
Huamei standard industry data sub-fee six
d. Manufacturer name.
7.2 Packaging
QB/T1446-1992
The packaging, marking and random documents of the concentrator shall comply with the relevant provisions of QB/T842.8. 7.3 Storage
The product shall be unpacked and inspected every six months since the date of packing, and anti-rust measures shall be taken again if necessary. 8 Quality Assurance
Under the conditions specified in the product manual, if the product is damaged or cannot work normally due to poor manufacturing quality within twelve months from the date of shipment from the manufacturer and is used for less than six months within this period, the manufacturer shall be responsible for free repair or replacement of parts (except wearing parts).
Additional remarks:
This standard is proposed by the Technical Equipment Department of the Ministry of Light Industry. This standard is under the jurisdiction of the National Light Industry Machinery Standardization Center. This standard was drafted by Shandong Jining Light Industry Machinery Factory and Shanghai Paper Machinery Factory Huguang Branch. The main drafters of this standard are Luo Yunnian and Cai Jinxiong. 118
Standard Technology Network Aw.bEOso
Cn Download various marking industry information
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.