JB/T 9889-1999 Precision test of slides for modular machine tools

JB/T 9889-1999 This standard is a revision of ZB J58 009-88 "Accuracy of mechanical slides for modular machine tools". During the revision, only editorial changes were made according to relevant regulations, and the technical content remained unchanged. This standard specifies the geometric accuracy requirements and inspection methods for the slides of modular machine tools. This standard is applicable to the slides of modular machine tools and their automatic lines. This standard was first issued in 1982 and revised for the first time in 1988. JB/T 9889-1999 Accuracy inspection of modular machine tool slides JB/T9889-1999 standard download decompression password: www.bzxz.net

ICS 25. (0160. 99
Machinery Industry Standard of the People's Republic of China
JBT9889-1999
Modular Machine Tool
Slide Table Accuracy Inspection
1999-05-20 Issued
State Machinery Industry Bureau
2000-01-01 Implementation
JB/T9889-1999
This standard is formulated on the basis of 2BJ58009-88 "Mechanical Sliding Standards for Combined Machine Tools". This standard is consistent with the technical content of ZBJ58009-88, and only the editing has been re-selected according to relevant regulations. This standard replaces ZBJ5B009-88 from the date of implementation. This standard is produced by the National Technical Committee for Standardization of Metal Cutting Machine Tools. This standard is purchased by the National Technical Committee for Standardization of Metal Cutting Machine Tools and the National Machine Tool Association. This standard is subject to the draft specification Location: Dalian Modular Machine Tool Research Institute. This standard was first issued in 1982 and revised for the first time in 1988. Scope
Machinery Industry Standard of the People's Republic of China
Modular Machine Tool
Slide Table Accuracy Inspection
The standard specifies the precision requirements and inspection methods for the precision of modular machine tools. This standard applies to modular machine tools and sliding tables of moving lines: 2 Referenced Standards
JB.T9889-1999
The following provisions, including those contained in the references in this standard, shall become part of this standard. The terms of the standard. This standard is published, and all copies are valid: All standards will be subscribed by you, so that all parties using this standard can explore the value of use, and the possibility of verifying the latest version is confirmed. 17421.1-199 Machine Tool Inspection Rules Part 1: What is the accuracy of the machine tool under no-load or precision working conditions? 3 Brief description
3.1 The nominal center size of the table is the saddle width of the corresponding slide. 3.2 When using this standard, refer to the relevant meanings of GB/T17421.1. 3.3 The special inspection items listed in this standard are not exhaustive. In order to reduce the loading and unloading and the inspection of the inspection, the inspection can be carried out in any order:
3.4 ​​The inspection tools and instruments specified in this standard are mandatory. In production, on the premise of ensuring the inspection accuracy, other inspection tools and instruments can be used.
4.1 In the inspection items using the ruler, both ends of the ruler should be supported in the best supporting position, with the length of the ruler corresponding to the length of the ruler, so as to minimize the self-winding
4.2 Place the slide on the inspection plate and use 0.03 Cut and check the gap between the sliding seat and the plate with a feeler gauge. The feeler gauge should be used to measure the depth of the slide. After the test, the center 16 precision width test is carried out. 4.3 Only when the dead stop iron of the platform is positioned by a work box, the G? item accuracy is considered to be tested, otherwise it is not tested. The GT test is carried out on the test bench.
Guohao Machinery Industry Bureau approved on May 20, 1999 and implemented on January 1, 2000
J798891999
Pear Clear Ball
z's ifzes | |tt | JBTB89-Www.bzxZ.net
IzE2 's
o0o1000
000T-0E9<
500'0800'0
JBT9889-1999
Ittt's
01009100
2E01000
120201059||tt| | 18000z100 |
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.